References
- [1] Arunachalam, R., Mannan, M.A. (2000). Machinability of Nickel-Based High Temperature Alloys. Machining Science and Technology 4, pp. 127-168. 10.1080/10940340008945703.
- [2] Arunachalam, R.M., Mannan, M.A., Spowage, A.C. (2004). Residual stress and surface roughness when facing age hardened Inconel 718 with CBN and ceramic cutting tools, International Journal of Machine Tools and Manufacture, 44, pp. 879-887. https://doi.org/10.1016/j.ijmachtools.2004.02.016.
- [3] Ayesta, I., Izquierdo, B., Flaño, O., Sánchez, J.A., Albizuri, J. and Avilés, R. (2016). Influence of the WEDM process on the fatigue behavior of Inconel® 718, International Journal of Fatigue, 92, pp. 220-233. 10.1016/j.ijfatigue.2016.07.011.
- [4] Berruti, T., Lavella, M. and Gola, M.M. (2009). Residual Stresses on Inconel 718 Turbine Shaft Samples After Turning, Machining Science and Technology, 13, pp. 543-560. 10.1080/10910340903451472.
- [5] Cullity, B.D. (1964). Podstawy dyfrakcji promieni rentgenowskich, Państwowe Wydawnictwo Naukowe.
- [6] Ezugwu, E.O. (2004). High speed machining of aero-engine alloys, Journal of the Brazilian Society of Mechanical Sciences and Engineering, 26, pp. 1-11. 10.1590/S1678-58782004000100001.
- [7] Fitzpatrick, M.E., Fry, A.T., Holdway, P., Kandil, F.A., Shackleton, J., Suominen, L. (2005). Determination of residual stresses by X-ray diffraction, Measurement Good Practice Guide No. 52, National Physical Laboratory.
- [8] Hilley, M.E. (Ed.) (1971). Residual stress measurement by X-ray diffraction-SAE J784a, Society of Automotive Engineers, Warrendale, PA.
- [9] Hua, Y. and Liu, Z. (2018). Experimental Investigation of Principal Residual Stress and Fatigue Performance for Turned Nickel-Based Superalloy Inconel 718, Materials, 11(6), p. 879. https://doi.org/10.3390/ma11060879.
- [10] Kawagoishi, N., Chen, Q., Kondo, E., Goto, M. and Nisitani, H. (1999). Influence of cubic boron nitride grinding on the fatigue strengths of carbon steels and a nickel-base superalloy, Journal of Materials Engineering and Performance, 8, pp. 152-158. https://doi.org/10.1361/105994999770346981.
- [11] Kortabarri, A., Madariag, A., Fernandez, E., Esnaol, J.A. and Arrazola, P.J. (2011). A comparative study of residual stress profiles on Inconel 718 induced by dry face turning, Procedia Engineering, 19, pp. 228-234. 10.1016/j.proeng.2011.11.105.
- [12] Lavella, M., and Berruti, T. (2009). Residual Stress on Inconel 718 Turbine Components after Machining, Key Engineering Materials, 417-418, pp. 601-604. https://doi.org/10.4028/www.scientific.net/kem.417-418.601.
- [13] Ma, Y., Zhang, J., Feng, P., Yu, D. and Xu, C. (2018). Study on the evolution of residual stress in successive machining process, The International Journal of Advanced Manufacturing Technology, 96, pp. 1025-1034. https://doi.org/10.1007/s00170-017-1542-0.
- [14] General Electric Internal Standard. (2017). Metallic test specimen preparation, low stress.
- [15] European Standard. (2008). Non-destructive testing — Test method for residual stress analysis by X-ray diffraction.
- [16] European Standard. Test Method for Verifying the Alignment of X-Ray Diffraction Instrumentation for Residual Stress.
- [17] Noyan, I.C., Cohen, J.B. (2013). Residual Stress: Measurement by Diffraction and Interpretation. Springer.
- [18] Outeiro, J.C., Pina, J.C., M’Saoubi, R., Pusavec, F. and Jawahir, I.S. (2008). Analysis of residual stresses induced by dry turning of difficult-to-machine materials. CIRP Annals, 57, pp. 77-80. https://doi.org/10.1016/j.cirp.2008.03.076.
- [19] Pawade, R.S., Joshi, S.S. and Brahmankar, P.K. (2008). Effect of machining parameters and cutting edge geometry on surface integrity of high-speed turned Inconel 718. International Journal of Machine Tools and Manufacture, 48, pp. 15-28. 10.1016/j.ijmachtools.2007.08.004.
- [20] Pei-zhuo, W., Zhan-shu, H., Yuan-xi, Z. and Shu-sen, Z. (2017). Control of Grinding Surface Residual Stress of Inconel 718. Procedia Engineering, 174, pp. 504-511. 10.1016/j.proeng.2017.01.174.
- [21] Prevéy, P.S. (1987). The measurement of subsurface residual stress and cold work distributions in nickel base alloys, Residual Stress in Design, Process and Materials Selection, WB Young, ed., ASME, Metals Park, OH, pp. 11-19.
- [22] Repper, J., Hofmann, M., Krempaszky, C., Wimpory, R.C., Petry, W. and Werner, E. (2009). Microstrain accumulation in multiphase superalloys, Powder Diffraction 24, pp. S65-S67. 10.1154/1.3134582.
- [23] Sharman, A.R.C., Hughes, J.I. and Ridgway, K. (2006). An analysis of the residual stresses generated in Inconel 718TM when turning, Journal of Materials Processing Technology 173, pp. 359-367.
- [24] Sinha, M.K., Setti, D., Ghosh, S. and Venkateswara Rao, P. (2016). An investigation on surface burn during grinding of Inconel 718, Journal of Manufacturing Processes 21, pp. 124-133. 10.1016/j.jmapro.2015.12.004.
- [25] Taricco, F. (2015). Effect of Machining and Shot Peening on the Residual Stresses of Superalloy Turbine Discs, Presented at the ASME 1995 International Gas Turbine and Aeroengine Congress and Exposition, American Society of Mechanical Engineers Digital Collection.
- [26] Wang, J., Zhang, D., Wu, B. and Luo, M. (2017). Numerical and Empirical Modelling of Machining-induced Residual Stresses in Ball end Milling of Inconel 718, Procedia CIRP, 16th CIRP Conference on Modelling of Machining Operations (16th CIRP CMMO) 58, pp. 7-12.
- [27] Yao, C.F., Jin, Q.C., Huang, X.C., Wu, D.X., Ren, J.X. and Zhang, D.H. (2013). Research on surface integrity of grinding Inconel718. The International Journal of Advanced Manufacturing Technology, 65, pp. 1019-1030. https://doi.org/10.1007/s00170-012-4236-7.