Ratcheting Simulation in a Titanium-Steel Bimetallic Plate Based on the Chaboche Hardening Model

Aleksander Karolczuk

doi:10.1515/ama-2016-0040

.blurhash-client-img { display: none !important; }

Ratcheting Simulation in a Titanium-Steel Bimetallic Plate Based on the Chaboche Hardening Model

Acta Mechanica et Automatica

Volume 10 (2016): Issue 4 (December 2016)

By: Aleksander Karolczuk

Open Access

|Dec 2016

Abstract

The paper presents the results of fatigue loading simulation applied to bimetallic model using the Chaboche kinematic hardening rule. Three cases of simulations were performed: (i) without residual stresses; (ii) considering residual stresses and (iii) considering asymmetrical geometry of bimetal, i.e. cross area reducing under tension period of loading. Experimental results exhibit the ratcheting phenomenon in titanium-steel bimetallic specimens. The observed ratcheting phenomenon could be explained by the third case of simulation which is supported by detection of microcracks in the vicinity of welded area.

References

1. Chaboche J., Dang Van K., Cordier G. (1979), Modelization of the strain memory effect on the cyclic hardening of 316 stainless steel, Structural mechanics in reactor technology. Transactions, Vol. L, 1-10.
Search in Google Scholar Back to article
2. Chaboche J.-L., Kanouté P. & Azzouz F. (2012), Cyclic inelastic constitutive equations and their impact on the fatigue life predictions, International Journal of Plasticity, 35, 44–66.10.1016/j.ijplas.2012.01.010
Search in Google Scholar Back to article
3. Crossland B. (1982), Explosive welding of metals and its application, Clarendon Press, Oxford.
Search in Google Scholar Back to article
4. Findik F. (2011), Recent developments in explosive welding, Materials & Design, 32 (3), 1081–1093.10.1016/j.matdes.2010.10.017
Search in Google Scholar Back to article
5. Ganczarski A., Szubartowski D. (2015), On The Stress Free Deformation Of Linear FGM Interface Under Constant Temperature, Acta Mechanica et Automatica, 9(3), 135-139.10.1515/ama-2015-0022
Search in Google Scholar Back to article
6. Gloc M., Wachowski M., Plocinski T., Kurzydlowski K.J. (2016), Microstructural and microanalysis investigations of bond titanium grade1/low alloy steel st52-3N obtained by explosive welding, Journal of Alloys and Compounds, 671, 446–451.10.1016/j.jallcom.2016.02.120
Search in Google Scholar Back to article
7. Gómez C., Canales M., Calvo S., Rivera R., Valdés J.R., Núñez, J.L. (2011), High and low cycle fatigue life estimation of welding steel under constant amplitude loading: Analysis of different multiaxial damage models and in-phase and out-of-phase loading effects, International Journal of Fatigue, 33 (4), 578–587.10.1016/j.ijfatigue.2010.10.015
Search in Google Scholar Back to article
8. Hubel H. (1996), Basic conditions for material and structural ratcheting, Nuclear Engineering and Design, 162(1), 55–65.10.1016/0029-5493(95)01136-6
Search in Google Scholar Back to article
9. Karolczuk A., Kowalski M. (2014), Fatigue phenomena in steel-titanium bimetallic composite (in Polish), Politechnika Opolska, Opole, Poland.
Search in Google Scholar Back to article
10. Karolczuk A., Kowalski M., Bański R., Żok F. (2013), Fatigue phenomena in explosively welded steel–titanium clad components subjected to push–pull loading, International Journal of Fatigue, 48, 101–108.10.1016/j.ijfatigue.2012.10.007
Search in Google Scholar Back to article
11. Karolczuk A., Kowalski M., Kluger K., Żok F. (2014), Identification of Residual Stress Phenomena Based on the Hole Drilling Method in Explosively Welded Steel-Titanium Composite, Archives of Metallurgy and Materials, 59 (3), 1129-1133.10.2478/amm-2014-0195
Search in Google Scholar Back to article
12. Lazurenko D.V., Bataev I.A., Mali V.I., Bataev A.A., Maliutina I.N., Lozhkin V.S., Esikov M.A., Jorge A.M.J. (2016), Explosively welded multilayer Ti-Al composites: Structure and transformation during heat treatment, Materials and Design, 102, 122–130.10.1016/j.matdes.2016.04.037
Search in Google Scholar Back to article
13. Paul H., Faryna M., Prażmowski M., Bański R. (2011), Changes in the bonding zone of explosively welded sheets, Archives of Metallurgy and Materials, 56 (2), 463–474.10.2478/v10172-011-0050-8
Search in Google Scholar Back to article
14. Paul H., Lityńska-Dobrzyńska L., Miszczyk M., Prażmowski M. (2012), Microstructure and Phase Transformations Near the Bonding Zone of Al/Cu Clad Manufactured by Explosive Welding, Archives of Metallurgy and Materials, 57 (4), 1151-1162.10.2478/v10172-012-0129-x
Search in Google Scholar Back to article
15. Song J., Kostka A., Veehmayer M., Raabe D. (2011), Hierarchical microstructure of explosive joints: Example of titanium to steel cladding, Materials Science and Engineering: A, 528 (6), 2641–2647.10.1016/j.msea.2010.11.092
Search in Google Scholar Back to article
16. Sulym H., Pasternak I., Tomashivskyy M. (2016), Boundary Integral Equations for an Anisotropic Bimaterial with Thermally Imperfect Interface and Internal Inhomogeneities, Acta Mechanica et Automatica, 10 (1), 66-74.10.1515/ama-2016-0012
Search in Google Scholar Back to article
17. Walczak Z. (1989), Explosive welding (in Polish), WNT.
Search in Google Scholar Back to article

Articles in this issue

DOI: https://doi.org/10.1515/ama-2016-0040 | Journal eISSN: 2300-5319 | Journal ISSN: 1898-4088

Journal RSS Feed

Language: English

Page range: 265 - 270

Submitted on: May 4, 2015

Accepted on: Nov 25, 2016

Published on: Dec 28, 2016

Published by: Bialystok University of Technology

In partnership with: Paradigm Publishing Services

Publication frequency: 4 issues per year

Keywords:

Ratcheting Phenomenon,

Explosive Welding,

Cyclic Loading,

The Chaboche Kinematic Hardening Model

Related subjects:

Engineering,

Electrical engineering,

Electronics,

Mechanical engineering,

Mechanics,

Bioengineering and biomedical engineering,

Biomechanics,

Civil engineering,

Environmental engineering

© 2016 Aleksander Karolczuk, published by Bialystok University of Technology
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Volume 10 (2016): Issue 4 (December 2016)