On the Eccentrically Loaded Socket Footings With Cut - Off Pyramid Shaped Socket

Major, Maciej; Major, Izabela; Kuchárová, Daniela; Kuliński, Krzysztof

doi:10.2478/cee-2019-0009

Abstract

In this work considerations concerning eccentrically loaded socket footing with cut-off pyramid shaped socket were presented. As an object of study sloped footing with 1.40 m height, corresponding to the maximum frost depth has been adopted. Knowing that in practice there are no perfect pure axial loads, load applied on the eccentricity has been taken into considerations. Eccentric loads result in footing rotation in the direction of eccentricity and acting load, hence one footing end is imbedding into the ground, whereas second end tries to rise up. To observe that phenomenon, elastic type of support under the foundation was introduced corresponding to the naturally humid sand with medium compaction. Presented in this paper considerations of innovative connection technology between footing and column were based on performed numerical studies. Advantages and disadvantages of presented footing in comparison to normal socket footings solutions were widely discussed. Numerical analyses were performed with the utilization Finite Element Method based SolidWorks software.

References

[1] PRZEWŁÓCKI, J. - DARDZIŃSKA, I. - ŚWINIAŃSKI, J.: Review of historical buildings' foundations. Geotechnique, Vol. 55, No. 5, 2005, pp. 363 - 372.10.1680/geot.2005.55.5.363
Search in Google Scholar Back to article
[2] PN-EN 1992-1-1:2008/Ap1:2010, Eurocode 2: Concrete constructions design procedures, Part 1-1: General requirements and requirements for buildings, PKN, Warszawa 2008 (in Polish).
Search in Google Scholar Back to article
[3] PN-EN 1997-1:2008, Eurocode 7: Geotechnical design, Part 1: General rules, PKN, Warszawa 2008 (in Polish).
Search in Google Scholar Back to article
[4] KNAUFF, M. - KNYZIAK, P. - GOLUBIŃSKA, A.: Tables and equations for the design of reinforced concrete elements with calculations examples. Second edition, PWN, Warszawa 2014, 443 p. (in Polish).
Search in Google Scholar Back to article
[5] STAROSOLSKI, W.: Reinforced concrete structures in reference to Eurocode 2 and other national standards. Vol. 3, PWN, Warszawa 2012, 682 p. (in Polish).
Search in Google Scholar Back to article
[6] KREJSA, M. – BROZOVSKY, J. – MIKOLASEK, D. – PARENICA, P. – FLODR, J. – MATERNA, A. – HALAMA, R. – KOZAK, J.: Numerical modelling of steel fillet welded joint. Advances in Engineering Software, Vol. 117, 2018, pp. 59 - 69.10.1016/j.advengsoft.2017.03.013
Search in Google Scholar Back to article
[7] KORMANIKOVA, E. – KOTRASOVÁ, K.: Finite Element Analysis of Damage Modelling of Fiber Reinforced Laminate Plate. Applied Mechanics and Materials, Vol. 617, 2014, pp. 247 - 250.10.4028/www.scientific.net/AMM.617.247
Search in Google Scholar Back to article
[8] LUO, N. - BATHURST, R. J.: Reliability bearing capacity analysis of footings on cohesive soil slopes using RFEM. Computers and Geotechnics, Vol. 89, 2017, pp. 203 - 212.10.1016/j.compgeo.2017.04.013
Search in Google Scholar Back to article
[9] MOAYEDI, H. - HAYATI, S.: Modelling and optimization of ultimate bearing capacity of strip footing near a slope by soft computing methods. Applied Soft Computing, Vol. 66, 2018, pp. 208 - 219.10.1016/j.asoc.2018.02.027
Search in Google Scholar Back to article
[10] JAVID, A. H. - FAHIMIFAR, A. - IMANI, M.: Numerical investigation on the bearing capacity of two interfering strip footings resting on a rock mass. Computers and Geotechnics, Vol. 69, 2015, pp. 514 - 528.10.1016/j.compgeo.2015.06.005
Search in Google Scholar Back to article
[11] MABROUKI, A. - BENMEDDOUR, D. - FRANK, R. - MELLAS, M.: Numerical study of the bearing capacity for two interfering strip footings on sands. Computers and Geotechnics, Vol. 37, No. 4, 2010, pp. 431 - 439.10.1016/j.compgeo.2009.12.007
Search in Google Scholar Back to article
[12] LOUKIDIS, D. - SALGADO, R.: Bearing capacity of strip and circular footings in sand using finite elements. Computers and Geotechnics, Vol. 36, No. 5, 2009, pp. 871 - 879.10.1016/j.compgeo.2009.01.012
Search in Google Scholar Back to article
[13] BENMEBAREK, S. - REMADNA, M. S. - BENMEBAREK, N. - BELOUNAR, L.: Numerical evaluation of the bearing capacity factor N’_γ of ring footings. Computers and Geotechnics, Vol. 44, 2012, pp. 132 - 138.10.1016/j.compgeo.2012.04.004
Search in Google Scholar Back to article
[14] MAJOR, M. - KULIŃSKI, K. - MAJOR, I.: Dynamic analysis of an impact load applied to the composite wall structure. MATEC Web of Conferences, Vol. 107, 2017, pp. 1 - 6.10.1051/matecconf/201710700055
Search in Google Scholar Back to article
[15] MAJOR, M. - KULIŃSKI, K. - MAJOR, I.: Innovative concrete-polyurethane composite blocks located in three-layer wall – thermal numerical analysis. Engineering Mechanics (red.) FUIS Vladimir, Brno, 2017, pp. 602 - 605.
Search in Google Scholar Back to article
[16] BADAKHSHAN, E. - NOORZAD, A.: Load eccentricity effects on behavior of circular footings reinforced with geogrid sheets. Journal of Rock Mechanics and Geotechnical Engineering, Vol. 7, No. 6, 2015, pp. 691 - 699.10.1016/j.jrmge.2015.08.006
Search in Google Scholar Back to article
[17] SHARMA, V. - KUMAR, A.: Behavior of ring footing resting on reinforced sand subjected to eccentric-inclined loading. Journal of Rock Mechanics and Geotechnical Engineering, Vol. 10, No. 2, 2018, pp. 347 - 357.10.1016/j.jrmge.2017.11.005
Search in Google Scholar Back to article
[18] CHEUNG, J. T. M. - ZHANG, M.: Finite element modelling of the human foot and footwear. ABAQUS Users’ Conference, 2006, pp. 145 - 159.
Search in Google Scholar Back to article
[19] KOIKE, S. - OKINA, S.: A modelling method of sport shoes for dynamic analysis of shoe-body coupled system. Procedia Engineering, Vol. 34, 2012, pp. 272 - 277.10.1016/j.proeng.2012.04.047
Search in Google Scholar Back to article
[20] CHO, J. R. - PARK, S. B. - RYU, S. H. - KIM, S. H. - LEE, S. B.: Landing impact analysis of sport shoes using 3-D coupled foot-shoe finite element model. Journal of Mechanical Science and Technology, Vol. 23, 2009, pp. 2583 - 2591.10.1007/s12206-009-0801-x
Search in Google Scholar Back to article

On the Eccentrically Loaded Socket Footings With Cut - Off Pyramid Shaped Socket

Abstract

Paradigm

My account