Optimizing Sampling Parameters of CMM Data Acquisition for Machining Error Correction of Freeform Surfaces

Poniatowska, Małgorzata

doi:10.2478/ama-2018-0040

Abstract

An optimization study using the design of experiment technique is described, in which the surface profile height of a freeform surface, determined in coordinate measurements, is the response variable. The control factors are coordinate sampling parameters, i.e. the sampling grid size and the measuring tip diameter. As a result of the research, an optimal combination of these parameters was found for surface mapping with acceptable measurement uncertainty. The presented study is the first stage of optimization of machining error correction for the freeform surface and was intended to take into account mechanical-geometric filtration of surface irregularities caused by these geometrical parameters. The tests were carried out on a freeform workpiece milled with specific machining parameters, Ra of the surface roughness was 1.62 μm. The search for the optimal combination of parameters was conducted using Statistica software.

References

1. Adamczak S., Janecki D, Makieła W., Stępień K. (2010), Quantitative comparison of cylindricity profiles measured with different methods using Legendre-Fourier coefficients, Metrology and Measurement Systems XVII, 233-244.10.2478/v10178-010-033-5
Search in Google Scholar Back to article
2. Al-Ahmari A.M.A., Aalam J. (2015), Optimizing parameters of freeform surface reconstruction using CMM, Measurement, 64, 17-28.10.1016/j.measurement.2014.12.031
Search in Google Scholar Back to article
3. Barini E. M., Tosello G., De Chifre L. (2010) Uncertainty analysis of point-by-point sampling complex surfaces using touch probe CMMs. DOE for complex surfaces verification with CMM, Precision Engineering, 34, 16-21.10.1016/j.precisioneng.2009.06.009
Search in Google Scholar Back to article
4. Chen Y., Tang H., Tang Q.,, Zhang A., Chen D., Li K., (2018), Machining error decomposition and compensation of complicated surfaces by EMD method, Measurement, 116, 341-349.10.1016/j.measurement.2017.11.027
Search in Google Scholar Back to article
5. Chena Y., Gaoa J.,, Deng H., Zhenga D., Chena X., Kelly R. (2013), Spatial statistical analysis and compensation of machining errors for complex surfaces, Precision Engineering 37, 203–212.10.1016/j.precisioneng.2012.08.003
Search in Google Scholar Back to article
6. Dietrich E., Schulze A. (2000), Statistical methods in qualification of measuring devices of machines and processes, Notika System, Warsaw (in Polish).
Search in Google Scholar Back to article
7. Feng C-X, Saal A. L., Salsbury J. G., Ness A. R., Lin G. C. S. (2007) Precision Engineering, 31, 94-101.10.1016/j.precisioneng.2006.03.003
Search in Google Scholar Back to article
8. ISO 14253-1:2014, Geometrical product specifications (GPS) – Inspection by measurement of workpieces and measuring equipment – Part 1: Decision rules for proving conformity or nonconformity with specification.
Search in Google Scholar Back to article
9. ISO 14253-2:2011, Geometrical product specifications (GPS) – Inspection by measurement of workpieces and measuring equipment – Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification.
Search in Google Scholar Back to article
10. ISO/IEC Guide 98-3:2008, Uncertainty of measurement – Part 3: Guide to the expression of uncertainty in measurement (GUM:1995).
Search in Google Scholar Back to article
11. Jakubiec W., Płowucha W., Starczak M. (2012), Analytical estimation of coordinate measurement uncertainty, Measurement, 45, 2299-2308.10.1016/j.measurement.2011.09.027
Search in Google Scholar Back to article
12. Karaszewski R., Skrzypczyńska K. (2013), Quality management, TNOiK, Toruń (in Polish).
Search in Google Scholar Back to article
13. Kowalczyk J. (1995), Quality management –Taguchi Method, Bellona, Warsaw (in Polish).
Search in Google Scholar Back to article
14. Mehrad V., Xue D., Gu P. (2013), Prediction of surface reconstruction uncertainties for freeform surface inspection, Measurement 2013, 46, 2682-2694.10.1016/j.measurement.2013.04.025
Search in Google Scholar Back to article
15. Moroni G., Petrò S. (2014), Optimal inspection strategy planning for geometric tolerance verification, Precision Engineering, 38, 71-8110.1016/j.precisioneng.2013.07.006
Search in Google Scholar Back to article
16. Obeidat S.M., Raman S.: An intelligent sampling method for inspecting free-form surfaces. International Journal Advanced Manufacturing Technology 2009, 40, 1125-1136.10.1007/s00170-008-1427-3
Search in Google Scholar Back to article
17. Poniatowska M. (2012), Deviation model based method of planning accuracy inspection of free-form surfaces using CMMs, Measurement, 45, 927-937.10.1016/j.measurement.2012.01.051
Search in Google Scholar Back to article
18. Rajamohan G., Shunmugam M. S., Samuel G. L. (2011a), Effect of probe size and measurement strategies on assessment of freeform profile deviations using coordinate measuring machine, Measurement, 44, 832-841.10.1016/j.measurement.2011.01.020
Search in Google Scholar Back to article
19. Rajamohan G., Shunmugam M.S., Samuel G.L. (2011b), Practical measurement strategies for verification of freeform surfaces using coordinate measuring machines, Metrology and Measurement Systems, XVIII, 209-222.10.2478/v10178-011-0004-y
Search in Google Scholar Back to article
20. Savio E., De Chiffre L, Schmitt R. (2007), Metrology of freeform shaped parts, Annals of the CIRP, 56, 810-835.10.1016/j.cirp.2007.10.008
Search in Google Scholar Back to article
21. Sladek J. A. (2016), Coordinate Metrology: Accuracy of Systems and Measurements. Springer, Berlin Heidelberg.
Search in Google Scholar Back to article
22. Weckenmann A, Estler T., Peggs G., Mc Murtry D. (2004), Probing Systems in Dimensional Metrology, CIRP Ann., 53, 657-684.10.1016/S0007-8506(07)60034-1
Search in Google Scholar Back to article

Optimizing Sampling Parameters of CMM Data Acquisition for Machining Error Correction of Freeform Surfaces

Abstract

Paradigm

My account