Constructional Features of Ropes in Functional Units of Mining Shaft Hoist

Mańka, Eugeniusz; Słomion, Małgorzata; Matuszewski, Maciej

doi:10.2478/ama-2018-0011

Abstract

In this paper structural analysis of steel ropes applied in mining shaft hoists was conducted. Functions of the ropes which they fulfilled in these shaft hoists were identified. Expected operational features of ropes were indicated too. An analysis was carried out four identified groups of ropes: hoisting ropes, balance ropes, leading rope and fender ropes. Basic constructional features: geometrical and material of ropes, which they should be characterized in each of mentioned functional groups were indicated. Constructional structures of mentioned steel ropes, the most often applied in domestic mining shaft hoists were described. Observed tendencies in analyzed issues also were shown.

References

1. Carbogno A., Fundalewicz Z., Mateja S. (2005), Safety of the round balancing rope type „SUPERFLEX”, Proceedings of International Conference „Shafts Transport 2005”, Institute of Mining Technology „KOMAG”, Gliwice – Zakopane, 221-232 (in Polish).
Search in Google Scholar Back to article
2. Carbogno A., Żołnierz M., Mateja S. (2010), Rope with surface contact of wires used in mining transport equipment, Proceedings of International Conference „Safety Operation of Mining Transport Equipment” Research and Supervisory Centre of Underground Mining, Lędziny – Ustroń, 45-55 (in Polish).
Search in Google Scholar Back to article
3. Catalogs of rope manufacturers: ArcelorMittal, Bourgan-Bresse Wire, Polish Ropes, Sosnowiec, Teufelberger, Wels, SAG, Katowice, SILTrade (in Polish).
Search in Google Scholar Back to article
4. Chang X.D., Peng Y.X., Zhu Z.C., Gong X.S., Yu Z.F., Mi Z.T., Xu C.M. (2017), Effects of strand lay direction and crossing angle on tribological behavior of winding hoist rope, Materials, 10, 630.10.3390/ma10060630555401128772992
Search in Google Scholar Back to article
5. Chang X.D., Peng Y.X., Zhu Z.C., Wang D.G., Gong X.S., Zou S.Y., Sun S.S., Mi Z.T., Xu W.X. (2016), Tribological properties of winding hoisting rope between two layers with different sliding parameters, Advances in Mechanical Engineering, 8(12), 1-14.10.1177/1687814016679911
Search in Google Scholar Back to article
6. Guo Y.B., Zhang D.K., Yang X.H., Feng C.N., Ge S.R. (2017), Experimental research on effect of wire rope transverse vibration on friction transmission stability in a friction hoisting system, Tribology International, 115, 233-245.10.1016/j.triboint.2017.05.033
Search in Google Scholar Back to article
7. Hansel J. (ed.) (2000), Steel-rubber balances ropes SAG. Scientific and Technical Papers KTL – AGH Kraków, 19, 1-125 (in Polish).
Search in Google Scholar Back to article
8. Kwaśniewski J. (2010), Magnetic steel ropes tests. AGH Publishers, Kraków (in Polish).
Search in Google Scholar Back to article
9. Li S.L., Hu P.Y., Zhao X.F., Chen K.J., Li J.K. (2017), Atmospheric corrosion performance of wire rope sling in a sulfur dioxide-polluted environment, Advances in Mechanical Engineering, 9(6), 1-12.10.1177/1687814017707479
Search in Google Scholar Back to article
10. Ma C., Xiao X.M. (2013), Kinetic analysis of a multi-rope friction mine hoist under overload conditions, Journal of Vibroengineering, 15(2), 925-932.
Search in Google Scholar Back to article
11. Ma Y.S., Xiao X.M. (2016), Dynamic analyses of hoisting ropes in a multi-rope friction mine hoist and determination of proper hoisting parameters, Journal of Vibroengineering, 18(5), 2801-2817.10.21595/jve.2016.16890
Search in Google Scholar Back to article
12. Mańka E. (2013), Comparative analysis of ropes test methods in terms of increasing accuracy and informativeness of the tests, Doctor’s dissertation, Faculty of Mechanical Engineering, University of Science and Technology in Bydgoszcz (in Polish).
Search in Google Scholar Back to article
13. Mańka E., Styp-Rekowski M. (2009), Diagnostic tests of balance ropes of mining hoist, Proceedings of International Conference „TEMAG” 2009, Silesian Technical University, Gliwice – Ustroń, 185-195 (in Polish).
Search in Google Scholar Back to article
14. Mateja S., Pojnar A. (2005), Analysis of the technical condition of the multi-layer balance rope Ø49 mm type NRHD-24 after the operation, Proceedings of International Conference „Shafts Transport 2005”, Institute of Mining Technology „KOMAG”, Gliwice – Zakopane, 241-251 (in Polish).
Search in Google Scholar Back to article
15. Milcarz T., Fundament K. (2005), Repair of flat steel-rubber balance rope SAG built in the hoist shaft IV N KWK „Sośnica, Proceedings of International Conference „Safety Operation of Mining Transport Equipment” Research and Supervisory Centre of Underground Mining, Lędziny – Szczyrk, 307-313 (in Polish).
Search in Google Scholar Back to article
16. Olszyna G., Sioma A., Tytko A. (2013), Assessment of the condition of hoisting ropes by measuring their geometric parameters in a three-dimensional image of their surface, Archives of Mining Sciences, 58(3), 643-654.10.2478/amsc-2013-0045
Search in Google Scholar Back to article
17. Peng Y.X., Chang X.D., Zhu Z.C., Wang D.G., Gong X.S., Zou S.Y., Sun S.S., Mi Z.T., Xu W.X. (2016), Sliding friction and wear behavior of winding hoisting rope in ultra-deep coal mine under different conditions, Wear, 368, 423-434.10.1016/j.wear.2016.10.012
Search in Google Scholar Back to article
18. Peterka P., Kresak J., Kropuch S., Fedorko G., Molnar V., Vojtko M. (2014), Failure analysis of hoisting steel wire rope, Engineering Failure Analysis, 45, 96-105.10.1016/j.engfailanal.2014.06.005
Search in Google Scholar Back to article
19. PN-EN 12385-2:2008, Steel ropes. Safety. Part 2: Definitions, markings and classification (in Polish).
Search in Google Scholar Back to article
20. PN-EN 12385-7:2004, Steel ropes. Safety. Part 7: Ropes closed construction for mining shafts (in Polish).
Search in Google Scholar Back to article
21. Sioma A., Tytko A. (2012), Vision methods for assessing the geometrical parameters of steel ropes, Acta Mechanica et Automatica, 6(1), 63-67.
Search in Google Scholar Back to article
22. Styp-Rekowski M., Mańka E. (2010), Environmental factors of rope hoisting shaft wear and reliability, Proceedings of X^th International Conference „Tribology and Reliability”, Petersburg State Transport University Publishing, St. Petersburg (Russia), 245-257.
Search in Google Scholar Back to article
23. Styp-Rekowski M., Mańka E., Matuszewski M., Madej M., Ozimina D. (2015), Tribological problems in shaft hoist ropes wear process, Industrial Lubrication and Tribology, 67(1), 47-51.10.1108/ILT-01-2014-0004
Search in Google Scholar Back to article
24. Wang X.Y., Meng X.B., Wang J.X., Sun Y.H., Gao K. (2015), Mathematical modeling and geometric analysis for wire rope strands, Applied Mathematical Modelling, 39(3-4), 1019-1032.10.1016/j.apm.2014.07.015
Search in Google Scholar Back to article
25. Xu L.M., Zhang D.K., Yin Y., Wang S.Q., Wang D.G. (2014), Fretting wear behaviors of hoisting rope wires in acid medium, Materials & Design, 55, 50-57.10.1016/j.matdes.2013.09.046
Search in Google Scholar Back to article
26. Zhang D.K., Feng C.A., Chen K., Wang D.G., Ni X. (2017), Effect of broken wire on bending fatigue characteristics of wire ropes, International Journal of Fatigue, 103, 456-465.10.1016/j.ijfatigue.2017.06.024
Search in Google Scholar Back to article
27. Zhang J., Wang D., Zhang D., Ge S.R., Wangb D. (2017), Dynamic torsional characteristics of mine hoisting rope and its internal spiral components, Tribology International, 109, 182-191.10.1016/j.triboint.2016.12.037
Search in Google Scholar Back to article
28. Zhao D., Liu S.G., Xu Q.T., Shi F., Sun W.Y., Chai L.Q. (2017), Fatigue life prediction of wire rope based on stress field intensity method, Engineering Failure Analysis, 81, 1-9.10.1016/j.engfailanal.2017.07.019
Search in Google Scholar Back to article

Constructional Features of Ropes in Functional Units of Mining Shaft Hoist

Abstract

Paradigm

My account