Possibilities of Heat Transfer Augmentation in Heat Exchangers with Minichannels for Marine Applications

Dariusz Mikielewicz; Jan Wajs

doi:10.1515/pomr-2017-0031

.blurhash-client-img { display: none !important; }

Possibilities of Heat Transfer Augmentation in Heat Exchangers with Minichannels for Marine Applications

Polish Maritime Research

Volume 24 (2017): Issue s1 (April 2017)

By: Dariusz Mikielewicz and Jan Wajs

Open Access

|May 2017

Abstract

In the paper, new trends in the development of microchannel heat exchangers are presented. The exchangers developed in this way can be applied in marine industry. Main attention is focused on heat exchanger design with reduced size of passages, namely based on microchannels. In authors′ opinion, future development of high power heat exchangers will be based on networks of micro heat exchangers.

References

1. Korczewski Z., Zacharewicz M.: Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility. Transactions of the Institute of Measurement and Control, 2012, Vol. 34, No.8, pp.937-946.10.1177/0142331211426170
Search in Google Scholar Back to article
2. Stolarski T.A.: Wear of water-lubricated composite materials. Wear, 1980, Vol.58, No.1, pp.103-108.10.1016/0043-1648(80)90215-X
Search in Google Scholar Back to article
3. Jakubowski M.: Influence of pitting corrosion on fatigue and corrosion fatigue of ship and offshore structures. Part II: Load - pit crack interaction. Polish Maritime Research, 2015, Vol.22, No.3, pp.57-66.10.1515/pomr-2015-0057
Search in Google Scholar Back to article
4. Ambroziak A., Kłosowski P.: Mechanical properties for preliminary design of structures made from PVC coated fabric. Construction and Building Materials, 2014, Vol.50, pp.74-81.10.1016/j.conbuildmat.2013.08.060
Search in Google Scholar Back to article
5. Ambroziak A., Kłosowski P.: Mechanical properties of polyvinyl chloride-coated fabric under cyclic tests. Journal of Reinforced Plastics and Composites, 2014, Vol.33, No.3, pp.225-234.10.1177/0731684413502858
Search in Google Scholar Back to article
6. Sabik A., Kreja I.: Large thermo-elastic displacement and stability FEM analysis of multilayered plates and shells. Thin-Walled Structures, 2013, Vol.71, pp.119-133.10.1016/j.tws.2013.05.002
Search in Google Scholar Back to article
7. Mikielewicz D., Klugmann M., Wajs J.: Flow boiling intensification in minichannels by means of mechanical flow turbulising inserts. International Journal of Thermal Sciences, 2013, Vol.65, pp.79-91.10.1016/j.ijthermalsci.2012.10.002
Search in Google Scholar Back to article
8. Szymkiewicz A., Modelling water flow in unsaturated porous media: Accounting for nonlinear permeability and material heterogeneity, Heidelberg, Springer, 2013.10.1007/978-3-642-23559-7
Search in Google Scholar Back to article
9. Wajs J., Mikielewicz D.: Effect of Surface Roughness on Thermal-hydraulic Characteristics of Plate Heat Exchanger. Key Engineering Materials, 2014, Vol.597, pp.63-74.10.4028/www.scientific.net/KEM.597.63
Search in Google Scholar Back to article
10. Cieśliński J.T., Mosdorf R.: Gas bubble dynamics - experiment and fractal analysis. International Journal of Heat and Mass Transfer, 2005, Vol.48, No.9, pp.1808-1818.10.1016/j.ijheatmasstransfer.2004.12.002
Search in Google Scholar Back to article
11. Wajs J., Mikielewicz D., Fornalik-Wajs E.: Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions. Journal of Physics Conference Series, 2016, Vol.745, 032063.10.1088/1742-6596/745/3/032063
Search in Google Scholar Back to article
12. Refprop v.9.0 National Institute of Standards, 2010.
Search in Google Scholar Back to article
13. Wilson E.E.: A basis for rational design of heat transfer apparatus Trans. ASME, 1915, Vol.37, pp.47-82.10.1115/1.4059736
Search in Google Scholar Back to article
14. Adams T.M., Abdel-Khalik S.I., Jeter S.M., Qureshi Z.H.: An experimental investigation of single-phase forced convection in microchannels. International Journal of Heat and Mass Transfer, 1998, Vol.41, pp.851-857.10.1016/S0017-9310(97)00180-4
Search in Google Scholar Back to article
15. Moffat R.J.: Describing the uncertainties in experimental results. Experimental Thermal and Fluid Science, 1988, Vol.1, pp.3-17.10.1016/0894-1777(88)90043-X
Search in Google Scholar Back to article
16. Zrooga A-B.S.R.: Experimental and theoretical study of boiling and dryout phenomenon of ethanol in vertical minitubes. (Ph.D. thesis) Gdansk University of Technology, 2010.
Search in Google Scholar Back to article
17. Deja M., Siemiątkowski M.S.: Feature-based generation of machining process plans for optimised parts manufacture. Journal of Intelligent Manufacturing, 2013, Vol.24, No.4, pp.831-846.10.1007/s10845-012-0633-x
Search in Google Scholar Back to article
18. Szłapczyński R.: Evolutionary Planning of Safe Ship Tracks in Restricted Visibility. Journal of Navigation, 2015, Vol.68, No.1, pp.39-51.10.1017/S0373463314000587
Search in Google Scholar Back to article

Articles in this issue

DOI: https://doi.org/10.1515/pomr-2017-0031 | Journal eISSN: 2083-7429 | Journal ISSN: 1233-2585

Journal RSS Feed

Language: English

Page range: 133 - 140

Published on: May 23, 2017

Published by: Gdansk University of Technology

In partnership with: Paradigm Publishing Services

Publication frequency: 4 issues per year

Keywords:

heat transfer intensification,

heat exchangers,

pumping power

Related subjects:

Engineering,

Introductions and overviews,

Engineering, other,

Geosciences,

Atmospheric science and climatology,

Life sciences,

Life sciences, other

© 2017 Dariusz Mikielewicz, Jan Wajs, published by Gdansk University of Technology
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Volume 24 (2017): Issue s1 (April 2017)