The research of anti corrosive properties of various compositions on samples of standard metals

Aghazada, Y.J.; Abbasov, Vaqif M.; Abdullayev, Sanan E.; Hasanov, Elgun K.; Suleymanova, Sevinc S.

doi:10.1515/pjct-2017-0071

Abstract

In this proceeding. the compositions of the T-30 turbine oil with liquid rubber. Co. Ni. Zn. Mg and Ba salts of the natural petroleum acids (NPA) boiling in the range 220–340°C and nitro compounds which are produced on the basis of C₁₄H₂₈ α-olefins have been investigated in different ratio and contents as metalworking fluids (MWF). The physical and chemical properties of the produced compositions have been studied. and the morphology of inhibited carbon steel surface was analyzed and characterized by using Fourier transform infrared (FTIR) and scanning electron microscopy (SEM) techniques. The effect of the temperature on the inhibition efficiency and thermodynamic parameters have also been reported. The thermal analyzer was used for the thermogravimetric analysis (TG/DTA) of the prepared MWF. The experiments have been operated with different concentrations of the inhibitor on the steel plates in condensation and environment phases in the experiment chamber.

References

1. Rozenfeld, I.L. 1981. Corrosion Inhibitors; McGraw-Hill. New York. p. 182.
Search in Google Scholar Back to article
2. Roberge, P.R. 2008. Corrosion Engineering Principle and Practice. McGraw-Hill. New York. 730 p.
Search in Google Scholar Back to article
3. McCoy, J.S. (2006). Introduction: Tracing the Historical Development of Metalworking Fluids, in Metalworking Fluids; Byers. J.P. Ed.; 2nd edition. Taylor & Francis. New York. pp. 1–18.
Search in Google Scholar Back to article
4. Brinksmeier, E., Meyer, D., Huesmann-Cordes, A.G. & Herrmann, C. (2015). Metalwor-king fluids-Mechanisms and performance. CIRP Ann. Manufact. Technol. 64, 605–628 (http://creativecommons.org/licenses/by-nc-nd/4.0/).
Search in Google Scholar Back to article
5. Hugh Spikes (2008). Low- and zero-sulphated ash. phosphorus and Sulphur anti-wear additives for engine oils. Lubrication Sci. 20, 103–136 DOI: 10.1002/ls.57.10.1002/ls.57
Open DOI Search in Google Scholar Back to article
6. Fouda, A.S., Elmorsi, M.A. & Abou-Elmagd, B.S. (2017). Adsorption and inhibitive properties of methanol extract of Eeuphorbia Heterophylla for the corrosion of copper in 0.5 M nitric acid solutions. Pol. J. Chem. Technol. 19(1), 95–103. DOI: 10.1515/pjct-2017-0014.10.1515/pjct-2017-0014
Search in Google Scholar Back to article
7. Dharma, R., Kodali. (2002). “High performance ester lubricants from natural oils”. Ind. Lubr. Tribol. 54(4) 165–170. http://dx.doi.org/10.1108/0036879021043171810.1108/00368790210431718
Open DOI Search in Google Scholar Back to article
8. Zvirko, O.I., Mytsyk, A.B., Tsyrulnyk, O.T., Gabetta, G. & Nykyforchyn, H.M. (2017). Corrosion Degradation of Steel of an Elbow of Gas Pipeline with Large-Scale Delamination after Long-Term Operation. Mater. Sci. 52(6). 861–865 https://doi.org/10.1007/s11003-017-0032-8.10.1007/s11003-017-0032-8
Search in Google Scholar Back to article
9. Ghai, I., Wentz, J., DeVor, R.E., Kapoor, S.G. & Samuel, J. (2010). Droplet behavior on a rotating surface for atomization-based cutting fluid application in micromachining. J. Manuf. Sci. Eng. 132(1). 011017 DOI:10.1115/1.400085910.1115/1.4000859
Open DOI Search in Google Scholar Back to article
10. Myshkin, N.K. & Markova, L.V. (2016). Methods and Instruments for Condition Monitoring of Lubricants. In: On-line Condition Monitoring in Industrial Lubrication and Tribology. Appl. Condit. Monitoring, 8, 1–29 Springer. Cham. https://doi.org/10.1007/978-3-319-61134-1_110.1007/978-3-319-61134-1_1
Search in Google Scholar Back to article
11. Zhao, F., Urbance, M. & Skerlos, S.J. (2004). Mechanistic Model of Coaxial Microfiltration for Semi-Synthetic Metalworking Fluid Microemulsions. J. Manufact. Sci. Enginee. 126(3), 435. http://doi.org/10.1115/1.1763187.10.1115/1.1763187
Open DOI Search in Google Scholar Back to article
12. Shujun, Gao, Peng, Jin, Bruce, Brown and etc. (2017). Corrosion behavior of mild steel in sour environments at elevated temperatures. Corrosion. Vol. 73. No. 8. pp. 915–926 https://doi.org/10.5006/236610.5006/2366
Open DOI Search in Google Scholar Back to article
13. Aiad, I., Riya, M.A., Tawfik, S.M. & Abousehly, A.M. (2016). Protection of carbon steel against corrosion in hydrochloric acid solution by some synthesized cationic surfactants. 52: 339. https://doi.org/10.1134/S207020511602002710.1134/S2070205116020027
Open DOI Search in Google Scholar Back to article
14. Skerlos, S.J., Rajagopalan, N., DeVor, R.E., Kapoor, S.G. & Angspatt, V.D. (2001). Microfiltration of Polyoxyalkylene Metalworking Fluid Lubricant Additives Using Aluminum Oxide Membranes. J. Manufact. Sci. Enginee. 123(4), 692. http://doi.org/10.1115/1.1392993.10.1115/1.1392993
Open DOI Search in Google Scholar Back to article
15. Thomas Norrby. (2003). Environmentally adapted lubricants – where are the opportu-nites? Ind. Lubr. Tribol. 5(6), 268–274. https://doi.org/10.1108/00368790310496400.10.1108/00368790310496400
Open DOI Search in Google Scholar Back to article
16. Skerlos, S.J. (2011). Cutting Fluids and their Environmental Impact. Chap. Encyclop. Tribol. Springer. http://doi.org/10.1007/978-0-387-92897-5.10.1007/978-0-387-92897-5
Open DOI Search in Google Scholar Back to article
17. MacLean, D., Hayes, K., Barnard, T., Hull, T., Park, Y.E. & Skerlos, S.J. (2009). Impact of Supercritical Carbon Dioxide Metalworking Fluids on Tool Life in turning of Sintered Steel and Milling of Compacted Graphite Iron. Proceed. ASME Inter. Manufact. Sci. Enginee. Conference 2009. MSEC2009, October 4–7, 2009. West Lafayette. Indiana. USA. pp. 43–48.10.1115/MSEC2009-84026
Search in Google Scholar Back to article
18. Singh, B.P., Nayak., S., Nanda. K., Bikash, K.J., Bhattacharjee, S. & Besra, L. (2013). The production of a corrosion resistant graphene reinforced composite coating on copper by electrophoretic deposition. Carbon 61, 47–56. DOI: 10.1016/j.carbon.2013.04.063.10.1016/j.carbon.2013.04.063
Open DOI Search in Google Scholar Back to article
19. Kaiyue, Li., Guoding Chen, Deng Liu. (2016). Study of the influence of lubrication parameters on gear lubrication properties and efficiency. Ind. Lubr. Tribol. 68(6). 647–657. https://doi.org/10.1108/ILT-06-2015-008910.1108/ILT-06-2015-0089
Open DOI Search in Google Scholar Back to article
20. Chang, S.C., Rihana, A., Bahrman, S., Gruden, C.L., Khijniak, A.I., Skerlos, S.J. & Adriaens, P. (2004). Flow cytometric detection and quantification of mycobacteria in metalworking fluids. Inter. Biodeterioration & Biodegradation 54(2–3), 105–112. http://doi.org/10.1016/j.ibiod.2004.03.01910.1016/j.ibiod.2004.03.019
Open DOI Search in Google Scholar Back to article
21. Hernández Gayosso, M.J. Nava, N. & Zavala, G. Olivares. (2016). Characterisation and comparison of corrosion products originated in steel pipelines transporting sour gas and crude oil. Inter. J. Corr. Process. Corr. Control 51(8), 626–634. http://dx.doi.org/10.1080/1478422X.2016.1173421.10.1080/1478422X.2016.1173421
Search in Google Scholar Back to article
22. Bhanudas Dattatraya Bachchhav, Geeta, S. Lathkar. Harijan Bagchi. (2014). Tribology of drawing lubricants for low carbon steel. Ind. Lubr. Tribol. 66(6), 640–644. https://doi.org/10.1108/ILT-10-2012-0105.10.1108/ILT-10-2012-0105
Open DOI Search in Google Scholar Back to article
23. Nasirov, F.A. (1983). Issledovaniye i razrabotca prochessa polucheniya nizcomolekulyar-noqo polibutadiyena v prisutstvii cataliticheskix sistem na osnove orqanichescix ditioproizvodnix nicelya (cobalta). Diss... cand.xim.nauk.. Baku. IPP ANAS 202 p.
Search in Google Scholar Back to article
24. ASTM C 613-14: ‘Standard test method for constituent content of composite prepreg by Soxhlet Extraction’.
Search in Google Scholar Back to article
25. van de Voort, F.R., Sedman, J. & Pinchuk, D. (2011). An overview of progress and new developments in FTIR lubricant condition monitoring methodology. J. ASTM Int. 8(5). ID: JAI103344Google Scholar.
Search in Google Scholar Back to article
26. Zimmerman, J.B., Hayes, K.F. & Skerlos, S.J. (2004). Influence of Ion Accumulation on the Emulsion Stability and Performance of Semi-Synthetic Metalworking Fluids. Enviromen. Sci. Technol, 38(8), 2482–2490. http://doi.org/10.1021/es034047710.1021/es034047715116857
Search in Google Scholar Back to article
27. Li Ming Chu, Jaw-Ren Lin, Yuh-Ping Chang. & Chung-Chun Wu. (2016). Elastohydrodynamic lubrication of circular contacts at pure squeeze motion with micropolar lubricants. Ind. Lubr. Tribol. 68(6) pp. 640–646. https://doi.org/10.1108/ILT-10-2015-0139.10.1108/ILT-10-2015-0139
Open DOI Search in Google Scholar Back to article

The research of anti corrosive properties of various compositions on samples of standard metals

Abstract

Paradigm

My account