References
- [1] Percina M., Aslantas K., Ucuna I., Kaynakb Y., Cicekc A., Micro-drilling of Ti–6Al–4V alloy: The effects of cooling/lubricating, Precision Engineering, Vol. 45/2016, 450–462.10.1016/j.precisioneng.2016.02.015
- [2] Rajurkar K.P, Sundaram M.M., Malshe A.P., Review of Electrochemical and Electrodischarge Machining, Procedia CIRP, Vol. 6/2013, 13–26.10.1016/j.procir.2013.03.002
- [3] Skoczypiec S., Machno M., Bizoń W., The capabilities of electrodischarge microdrilling of high aspect ratio holes in ceramic materials, Management and Production Engineering Review Vol. 6-3/2015, 61–69.10.1515/mper-2015-0027
- [4] Plaza S., Sanchez J.A., at all, Experimental study on micro EDM-drilling of Ti6Al4V using helical electrode, Prec. Eng. Vol. 38/2014, 821–827.10.1016/j.precisioneng.2014.04.010
- [5] Skoczypiec S., Ruszaj A., A sequential electrochemical-electrodischarge process for micro part manufacturing Prec. Eng., Vol. 38/2014, 680–690.10.1016/j.precisioneng.2014.03.007
- [6] Hasan M., Zhao J., Jiang Z., A review of modern advancements in micro drilling techniques Journal of Manufacturing Process, Vol. 29/2017, 343–375.10.1016/j.jmapro.2017.08.006
- [7] Kliuev M., Baumgart C., Wegener K., Fluid dynamics in Electrode Flushing Channel and Electrode-Workpiece Gap During EDM Drilling, “Procedia CIRP”, Vol. 68/2018, 254–259.10.1016/j.procir.2017.12.058
- [8] Li J., Yin G., Wang C., Guo X., Yu Z., Prediction of aspect ratio of a micro hole drilled by EDM “Journal of Mechanical Science and Technology”, Vol. 27/2013, 185–190.10.1007/s12206-012-1214-9
- [9] Kamal K., Rawalb S.K., Singha V.P., Anu B., Experimental Study on Diametric Expansion and Taper Rate in EDM Drilling For High Aspect Ratio Micro Holes in High Strength Materials, “Materials Today: Proceedings”, Vol. 5/2018, 7363–7372.10.1016/j.matpr.2017.11.406
- [10] Risto M., Haas R., Munz M., Optimization of the EDM drilling process to increase the productivity and geometrical accuracy, “Procedia CIRP” Vol. 42/2016, 537–542.10.1016/j.procir.2016.02.247
- [11] Mowwer T.D., Degradation of titanium 6Al–4V fatigue strength due to electrical discharge machining, “International Journal of Fatigue”, Vol. 64/2014, 84–96.10.1016/j.ijfatigue.2014.02.018
- [12] Manjaiah M., Narendranath S., Basavarajappa S., A review on machining of titanium based alloys using EDM and WEDM, “Rev. Adv. Mater. Sci.” Vol. 36/2014, 89–111.
- [13] Antar M., Chantzis D. et al., High Speed EDM and Laser Drilling of Aerospace Alloys, “Procedia CIRP”, Vol. 42/2016, 526–531.10.1016/j.procir.2016.02.245
- [14] Hasçalık A., Çaydas U., Electrical discharge machining of titanium alloy (Ti–6Al–4V), “Applied Surface Science”, Vol. 253/2007, 9007–9016.10.1016/j.apsusc.2007.05.031
- [15] Sanchez J. A., Plaza S., et al., Electrode set-up for EDM-drilling of large aspect-ratio microholes, “Procedia CIRP” Vol. 6/2013, 274–279.10.1016/j.procir.2013.03.009
- [16] Ezugwu E.O., Wang Z.M., Titanium alloys and their machinability – a review, “Journal of Materials Processing Technology”, Vol. 68/1997, 262–274.10.1016/S0924-0136(96)00030-1
- [17] Hascalik A., Caydas U., Electrical discharge machining of titanium alloy (Ti–6Al–4V), “Applied Surface Science”, Vol. 253/2007, 9007–9016.10.1016/j.apsusc.2007.05.031
- [18] Wansheng Z., Zhenlong W., Schichun D., Guanxin C., Hongyu W., Ultrasonic and electro discharge machining to deep and small hole on titanium alloy, “Journal of Materials Processing Technology”, Vol. 120/2002, 101–106.10.1016/S0924-0136(01)01149-9
- [19] Fonda P., Wang Z., Yamazaki K., Akutsu Y., A fundamental study on Ti–6Al–4V’s thermal and electrical properties and their relation to EDM productivity, “J. Mater. Process. Technol”, Vol. 202/2008, 583–589.10.1016/j.jmatprotec.2007.09.060