References
- 1. M. FONTAINE, A. DEVILLEZ, A. MOUFKI, D. DUDZINSKI. 2007. Modeling of cutting forces in ball end milling with tool surface inclination, Part II. Influence of cutting conditions, run-out, ploughing and inclination angle. J. Mater. Process. Technol., 189(1–3), pp. 85–89.
- 2. A. DAYMI, M. BOUJELBENE, J.M. LINARES, E. BAYRAKTAR, A. BEN AMARA. 2009. Influence of workpiece inclination angle on the surface roughness in ball end milling of the titanium alloy Ti–6Al–4V. J. Achiev. Mater. Manuf. Eng., 35(1), pp. 79–86.
- 3. C.E.H. VENTURA, A. HASSUI. 2013. Evaluation of static cutting forces and tool wear in HSM process applied to pocket milling. Int. J. Adv. Manuf. Tech. 65, pp. 1681-1689.
- 4. T. VOPÁT, J. PETERKA, V. ŠIMNA, M. KURUC. 2015. The influence of different types of copy milling on the surface roughness and tool life of end mills. Procedia Engineering, Vol. 100, pp. 868–876. ISSN 1877-7058
- 5. D. BEGIC-HAJDAREVIC, M. KULENOVIC, A. CEKIC. 2014. Experimental study on the high speed machining of hardened steel. Procedia Engineering, Vol. 69, pp. 291–295.
- 6. T. XIANHUA, Z. JUN. 2013. Effect of cutting speed on cutting forces and wear mechanisms in high-speed face milling of Inconel 718 with Sialon ceramic tools. Int. J. Adv. Manuf. Tech. 69, pp. 2669-2678.
- 7. C. XIAOXIAO, Z. JUN, H. SHIGUO. 2013. Effects of inclination angles on geometrical features of machined surface in five-axis milling. Int. J. Adv. Manuf. Tech. 65, pp. 1721-1733,
- 8. H. SCHULZ, S. HOCK. (1995). High-speed milling of die and moulds – cutting conditions and technology. Annals of the CIRP, 44, pp. 35-38.
- 9. Z. SONG, L. JIAN-FENG. 2010. Tool wear criterion, tool life, and surface roughness during high speed steel end milling Ti-6Al-4V. J. Zhejiang Univ. Sci., A. 8, pp. 587-595.
- 10. K.A. KADIRGAMAA, A. ABOU-EL-HOSSEINB. 2011. Tool life and wear mechanism when machining Hastelloy C-22HS. Elsevier Wear, 270, pp. 258–268.
- 11. Q. XINYI, L. PENGNAN. 2014. Study on serrated chip formation and tool wear of cermet tools for milling stainless steel 3Cr13Cu. Int. J. Adv. Manuf. Tech., 77, pp. 461-467.
- 12. M.B. DA SILVA, V.T.G. 2011. Naves, Analysis of wear of cemented carbide cutting tools during milling operation of gray iron and compacted graphite iron. Wear, 271, pp. 2426-2432.
- 13. M. ZETEK. I. CESAKOVA, V. SVARC. 2014. Increasing Cutting Tool Life when Machining Inconel 718. Procedia Engineering, Vol. 69, pp. 1171–1179.
- 14. M.S. KASIMA. C.H. CHE HARONB, J.A. GHANIB et al. 2013. Wear mechanism and notch wear location prediction model in ball nose end milling of Inconel 718. Wear, 302(1–2).
- 15. J. URMINSKÝ, R. ZAUJEC. 2018. Analysis of hardfacing and milling of forging die by CAx technologies. Materials Science Forum, Vol. 919, s. 354-361. ISSN 0255-5476
- 16. C.C. TAI, K.H. FHU. 1994. A predictive force model in ball-end milling including eccentricity effects. Int. J. Mach. Tools Manufact. 34, pp. 959–979.
- 17. J. PETERKA. 1997. Rozbor geometrie a kinematiky kopírovacieho frézovania. (Analysis of the geometry and kinematics of copy milling.) In: Vedecké práce MTF STU in Trnava, 5, pp. 53-58. ISBN 80-227-1005-9