References
- 1. J. Lundberg, ‘Undocumented oil leakages: A study about stern tube seals and leakages’, Dissertation, 2021.
- 2. Kelly, C. A., et al. ‘Underwater emissions from a two-stroke outboard engine: a comparison between an EAL and an equivalent mineral lubricant’, Materials & Design 26.7, 609–617, 2005.10.1016/j.matdes.2004.08.013
- 3. W. Litwin and A. Olszewski, ‘Assessment of possible application of waterlubricated sintered brass slide bearing for marine propeller shaft’, Polish Marit. Res., 19,1, 54–61, 2012.10.2478/v10012-012-0040-4
- 4. M. Wodtke and W. Litwin, ‘Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects’, Tribology International, 153, 106608, 2021.10.1016/j.triboint.2020.106608
- 5. W. Litwin and C Dymarski, ‘Experimental research on water-lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear’, Tribology International, 95, 449–455, 2016.10.1016/j.triboint.2015.12.005
- 6. Z. Guo, Ch. Yuan, A. Liu and S. Jiang, ‘Study on tribological properties of novel biomimetic material for water-lubricated stern tube bearing’, Wear, 376–377, 911–919, 2017.10.1016/j.wear.2017.01.081
- 7. J. C. J. Bart, E. Gucciardi and S. Cavallaro, ‘Renewable feedstocks for lubricant production’, Biolubricants, 121–248, 2013.10.1533/9780857096326.121
- 8. A. Młynarczak, K. Rudzki, ‘Optimisation of the topping-up process of lubricating oil in medium-speed marine engines’, Polish Marit. Res., 28, 2, 78–84, 2021.10.2478/pomr-2021-0024
- 9. F. J. Owuna, ‘Stability of vegetable based oils used in the formulation of ecofriendly lubricants – a review’, Egypt. J. Pet., 29, 251–256, 2020.10.1016/j.ejpe.2020.09.003
- 10. R. Bayat and A. Lehtovaara, ‘EHL/mixed transition of fully formulated environmentally acceptable gear oils’, Tribol. Int., 146, 106158, 2020.10.1016/j.triboint.2020.106158
- 11. Borras, F. Xavier, Matthijn B. De Rooij and Dik J. Schipper, ‘Rheological and wetting properties of environmentally acceptable lubricants (EALs) for application in stern tube seals’, Lubricants 6.4, 100, 2018.10.3390/lubricants6040100
- 12. Yano, Akihiko, et al. ‘Study on the load carrying capacity of sliding bearing lubricated by synthetic ester oils’, Tribology Online 10.5, 377–389, 2015.10.2474/trol.10.377
- 13. W. Litwin, ‘Water-lubricated bearings of ship propeller shafts - Problems, experimental tests and theoretical investigations’, Polish Marit. Res., 16, 4, 41–49, 2009.10.2478/v10012-008-0055-z
- 14. W. Litwin, ‘Influence of main design parameters of ship propeller shaft water-lubricated bearings on their properties’, Polish Marit. Res., 17, 4, 39–45, 2010.10.2478/v10012-010-0034-z
- 15. G. N. Rossopoulos, Ch. I. Papadopoulos and Ch. Leontopoulos, ‘Tribological comparison of an optimum single and double slope design of the stern tube bearing, case study for a marine vessel’, Tribology International, 150, 106343, 2020.10.1016/j.triboint.2020.106343
- 16. T. He, D. Zou, X. Lu, Y. Guo, Z. Wang and W. Li, ‘Mixed-lubrication analysis of marine stern tube bearing considering bending deformation of stern shaft and cavitation’, Tribology International, 73, 108–116, 2014.10.1016/j.triboint.2014.01.013