A new approach to flux deposition for brazing aluminium by low pressure cold spraying
References
- Fabian R. Vacuum technology: practical heat treating and brazing. ASM International; Ohio, 1993.
- Singh M, Ohji T, Asthana R. Green and sustainable manufacturing of advanced material. Oxford (UK): Elsevier; 2015.
- Shah RK. Advances in automotive heat exchanger technology. SAE Int. 2003;112: 631–41.
- Mirski Z, Pabian J. Modern trends in production of brazed heat exchangers for automotive industry. Weld Technol Rev. 2017;89(8): 5–12.
- Mirski Z, Pabian J, Wojdat T, Hejna J. Significance of the brazing gap in the brazing of aluminium heat exchangers for automotive industry. Weld Technol Rev. 2020;92(4): 7–14.
- Woods R. CAB brazing metallurgy. 12th annual international invitational aluminum brazing seminar. Michigan (MI), USA: AFC Holcroft, NOVI; 2007.
- Kuczmaszewski J, Zalewski K. Machining of aluminum and magnesium alloys. Lublin, Poland: Lublin University of Technology; 2015.
- Orman L, Swidersky HW, Lauzon D. Brazing of aluminium alloys with higher magnesium content using non-corrosive fluxes. Alum Brazing. 2014;52: 24–9.
- Zhao H, Woods R. 10 – Controlled atmosphere brazing of aluminum. In: Dušan P Sekulić (ed.) Woodhead publishing series in welding and other joining technologies. Adv Brazing. Woodhead Publishing; Sawston (UK), 2013. p. 280–23.
- Mirski Z, Granat K, Misiek A. Brazing of aluminum heat exchangers in the automotive industry. Spajanie materiałów konstrukcyjnych. 2015;28(2): 32–4.
- Hu J, Zhang Q. Investigation of pseudo-ternary system AlF3–KF–KCl. Thermochim Acta. 2003;404(1–2): 3–7.
- Markovits T, Takács J, Lovas A, Belt J. Laser brazing of aluminium. J Mater Process Technol. 2003;143–144: 651–5.
- Pabian J. Analysis of erosion phenomena in brazing of aluminum heat exchangers. Scientific seminar. Wrocław, Poland: Wroclaw University of Technology; 2018.
- Orman L. Quality tests of brazed plate heat exchangers using paint flux technology. Internal Report for Valeo. Valeo, Skawina, Poland; 2017.
- European Committee for Electrotechnical Standardization (CENELEC). Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: design, construction, testing, marking and documentation. Brussels: CENELEC; 2017. Standard No. SIST EN 378–2:2017.
- Nastic A, Jodoin B, Legoux JG, Poirier D. Particle impact characteristics influence on cold spray bonding: investigation of interfacial phenomena for soft particles on hard substrates. J Therm Spray Technol. 2021;30: 2013–33.
- Yin S, Suo X, Liao H, Guo Z, Wang X. Significant influence of carrier gas temperature during the cold spray process. Surf Eng. 2014;30(6): 443–50.
- Singh S, Raman RKS, Berndt CC, Singh H. Influence of cold spray parameters on bonding mechanisms: a review. Metals. 2021;11: 2016.
- Brusentseva T, Shikalov V, Lavruk S, Fomin V. Simulation of thermoplastic powder cold spraying. J Sib Fed Univ Math Phys. 2021;14(6): 726–34.
- Haban I, Sun Y, Veysset D, Nelson KA, Schuh CA. The effect of substrate temperature on the critical velocity in microparticle impact bonding. Appl Phys Lett. 2021;119: 011903
- da Silva FS, Bedoya J, Dosta S, Cinca N, Cano IG, Guilemany JM, et al. Corrosion characteristics of cold gas spray coatings of reinforced aluminum deposited onto carbon steel. Corros Sci. 2017;114: 57–71
- Winnicki M, Baszczuk A, Jasiorski M, Borak B, Małachowska A. Preliminary studies of TiO2 nanopowder deposition onto metallic substrate by low pressure cold spraying. Surf Coat Technol. 2019;371: 194–202
- Baszczuk A, Jasiorski M, Winnicki M. Low-temperature transformation of amorphous Sol–Gel TiO2 powder to anatase during cold spray deposition. J Therm Spray Tech. 2018;27: 1551–62.
- Winnicki M. Advanced functional metal-ceramic and ceramic coatings deposited by low-pressure cold spraying: a review. Coatings. 2021;11: 1044.
- European Committee for Electrotechnical Standardization (CENELEC). Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: chemical composition and form of products. Brussels: CENELEC; 2014. Standard No. EN 573–3:2014.
- European Committee for Electrotechnical Standardization (CENELEC). Welding consumables: wire electrodes, wires and rods for welding of aluminium and aluminium alloys: classification. Brussels: CENELEC; 2016. Standard No. EN ISO 18273:2016.
- Massalski TB. Binary alloys phase diagrams. ASM International. Vol. 1; Ohio, 1992.
- Eustathopoulos N, Nicholas M, Drevet B. Wettability at high temperatures. Pergamon materials series. Pergamon, Oxford (UK). Vol. 3; 1999.
- Schwartz MM. Brazing, second edition. Mel M. Schwartz (Ed.) In: The materials informations society. Ohio (OH), USA: ASM International; 2003.
- Roberts P. Industrial brazing practice. 2nd ed. London: CRC Press. Taylor and Francis Group; 2013.
- Swiderski HW, Lauzon D. Myths about aluminium brazing with non-corrosive fluxes NOCOLOK: Flux Brazing Technology. Materials of Solvay Flux GmbH. May 2001, Aachen, Germany. Available from: http://www.aluminium-brazing.com/sponsor/nocolok/Files/PDFs/31390.pdf
- Swidersky HW, Ottmann A, Belt H. Comparison of flux characteristics and flux transfer systems in electrostatic NOCOLOK® flux application for aluminum brazing. Invitational aluminum brazing seminar: Thermal Alliance Internationl; Detroit, 1999.
- Milani SAAH. Effect of NOCOLOK flux dry-off temperature on mechanical properties of brazed joint for automotive aluminum-based heat exchangers. Eng Res Express. 2020;2: 025003.
- Wang Z, Cai S, Jin K, Wang X, Chen W. In-flight aggregation and deposition behaviour of particles in low pressure cold spray. Surf Coat Technol. 2021;409: 126875.
- Alonso L, Garrido MA, Poza P. An optimisation method for the cold-spray process: on the nozzle geometry. Mater Des. 2022;214: 110387.
- Buhl S, Breuninger P, Antonyuk S. Optimization of a laval nozzle for energy-efficient cold spraying of microparticles. Mater Manuf Processes. 2018;33(2): 115–22.
- Winnicki M, Piwowarczyk T, Małachowska A. General description of cold sprayed coatings formation and of their properties. Bull Pol Acad Sci Techn Sci. 2018;66(3): 301–10.
- Baranowski M, Bober M, Kudyba A, Sobczak N. The effect of surface condition on wetting of hastelloy® X by brazing filler metal of Ni-Pd-Cr-B-Si system. J Mater Eng Perform. 2019;28: 3950–9.
- Chung CL, Moon KS, Wong CP. Influence of flux on wetting behavior of lead-free solder balls during the infrared-reflow process. J Electron Mater. 2005;34: 994–1001.
- Yao Z, Xue S, Zhang J. Comparative study on the activity of GaF3 and Ga2O3 nanoparticle-doped CsF-AlF3 flux for brazing 6061 Al/Q235 steel joints. Crystals. 2020;10: 498–508.
- Nylén M, Gustavsson U, Hutchinson W, Karlsson Å, Johansson H. Mechanisms of erosion during brazing of aluminium alloys. Mater Sci Forum. 2002;396–402: 1585–90.
- Krystek K, Krzanowska K, Wierzbińska M, Motyka M. The effect of selected process conditions on microstructure evolution of the vacuum brazed joints of hastelloy X nickel superalloy sheet. Arch Metall Mater. 2022;67(4): 1551–61.
- Lacaze J, Tierce S, Lafont M-C, Thebault Y, Pébère N, Mankowski G, et al. Study of the microstructure resulting from brazed aluminium materials used in heat exchangers. Mater Sci Eng A. 2005; 413–414: 317–21.
Language: English
Page range: 114 - 124
Submitted on: Jan 10, 2023
Accepted on: Mar 8, 2023
Published on: Apr 20, 2023
Published by: Sciendo
In partnership with: Paradigm Publishing Services
Publication frequency: 4 times per year
Keywords:
Related subjects:
© 2023 Tomasz Wojdat, Marcin Winnicki, Jaroslaw Pabian, published by Sciendo
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.