Abrasive Water Jet Cutting of Stainless-Steel Optimization by Orthogonal Array Approach
References
- 1. L. Kukiełka
et al. , “Analysis of the States of Deformation and Stress in the Surface Layer of the Product after the Burnishing Cold Rolling Operation,”Materials Science Forum , vol.862 (2016), pp. 278–287. - 2. R. Patyk
et al. , “Experimental and numerical researches of duplex burnishing process in aspect of achieved productive quality of the product,”AIP Conference Proceedings , vol.1960 , no. 1, (2018) p. 070021. - 3. A. Perec, “Environmental Aspects of Abrasive Water Jet Cutting,”
Annual Set The Environment Protection - Rocznik Ochrona Srodowiska , vol.20 ( 2018), pp. 258–274. - 4. J. Valíček, S. Hloch, and D. Kozak, “Surface geometric parameters proposal for the advanced control of abrasive waterjet technology,”
The International Journal of Advanced Manufacturing Technology , vol.41 , no. 3–4, (2009) pp. 323–328.10.1007/s00170-008-1489-2 - 5. A. Perec, “Experimental research into alternative abrasive material for the abrasive water jet cutting of titanium,”
Int. J. Adv. Manuf. Technol. , vol.97 , no. 1–4, (2018), pp. 1529–1540. - 6. P. D. Unde, M. D. Gayakwad, N. G. Patil, R. S. Pawade, D. G. Thakur, and P. K. Brahmankar, “Experimental Investigations into Abrasive Waterjet Machining of Carbon Fiber Reinforced Plastic,”
Journal of Composites , 2015. [Online]. Available:https://www.hindawi.com/journals/jcomp/2015/971596/ . [Accessed: 06-Jul-2018]. - 7. D. G. Alberts and M. Hashish, “Evaluation of submerged high-pressure waterjets for deep ocean applications,” in
Proceedings of the Sixth (1996) International Offshore and Polar Engineering Conference, Vol I, 1996 , J. S. Chung, B. M. Das, and J. Roesset, Eds. Cupertino: International Society Offshore& Polar Engineers, (1996), pp. 46–50. - 8. J. Foldyna, P. Martinec, and L. Sitek, “Testing of mineral typed of abrasives for abrasive water jet cutting,” in
2001 WJTA American Waterjet Conference. Minneapolis, Minnesota, USA , 2001, Paper 22. - 9. S. Hloch and J. Valicek, “Significance of Barton Garnet and Olivine Evaluation at Abrasive Waterjet Cutting by Factor Analysis,”
Nonconventional Technologies Review , no. 4, (2007), pp. 25–30. - 10. D. Kinik, B. Gánovská, S. Hloch, P. Monka, K. Monková, and Z. Hutyrová, “On-line monitoring of technological process of material abrasive water jet cutting | On-line praćenje tehnološkog postupka rezanja materijala abrazivnim vodenim mlazom,”
Techničky vjesnik , vol.22 , no. 2, (2015), pp. 351–357. - 11. M. Tavodová, “The surface quality of materials after cutting by abrasive water jet evaluated by selected methods,”
Manufacturing Technology , vol.13 , no. 2, (2013), pp. 236–241. - 12. V. Sharma, S. Chattopadhyaya, and S. Hloch, “Multi response optimization of process parameters based on Taguchi-Fuzzy model for coal cutting by water jet technology,”
International Journal of Advanced Manufacturing Technology , vol.56 , no. 9–12, (2011), pp. 1019–1025. - 13. A. Perec, “Abrasive suspension water jet cutting optimization using orthogonal array design,”
Procedia Engineering , vol.149 , (2016), pp. 366–373. - 14. A. Perec, F. Pude, M. Kaufeld, and K. Wegener, “Obtaining the Selected Surface Roughness by Means of Mathematical Model Based Parameter Optimization in Abrasive Waterjet Cutting,”
Strojniški vestnik - Journal of Mechanical Engineering , vol.63 , no. 10, (2017), pp. 606–613. - 15. P. Martinec, J. Foldyna, L. Sitek, J. Ščučka, and J. Vašek, “Abrasives for AWJ cutting. INCO-COPERNICUS,” Institute of Geonics, Ostrava, 2002, ISBN 80-86407-02-0, 2002.
- 16. A. Perec, “Investigation of Limestone Cutting Efficiency by the Abrasive Water Suspension Jet,” in
Advances in Manufacturing Engineering and Materials: Proceedings of the International Conference on Manufacturing Engineering and Materials (ICMEM 2018), 18–22 June, 2018, Nový Smokovec, Slovakia , S. Hloch, D. Klichová, G. M. Krolczyk, S. Chattopadhyaya, and L. Ruppenthalová, Eds. Springer International Publishing, 2019. - 17. H. Hocheng and M. Y. Hsu, “Erosion wear of stainless steel by abrasives entrained in a water jet,”
Arabian Journal for Science and Engineering , vol.25 , no. 2, (2000) pp. 187–202. - 18. P. Hreha, S. Hloch, and V. Peržel, “Analysis of acoustic emission recorded during monitoring of abrasive waterjet cutting of stainless steel AISI 309,”
Tehnički vjesnik , vol.19 , no. 2, (2012) pp. 355–359. - 19. S. B. Supriya and S. Srinivas, “Machinability Studies on Stainless Steel by Abrasive Water Jet - Review,”
Materials Today: Proceedings , no. 5, (2018), pp. 2871–2876.10.1016/j.matpr.2018.01.079
Language: English
Page range: 55 - 61
Published on: Dec 31, 2019
Published by: Lucian Blaga University of Sibiu
In partnership with: Paradigm Publishing Services
Publication frequency: 1 times per year
Related subjects:
© 2019 Andrzej Perec, Aleksandra Radomska-Zalas, published by Lucian Blaga University of Sibiu
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.