Experimental Estimation of Wear Resistance of Polyamide Composites, Reinforced By Carbon and Glass Fibres Used in Metal-Polymer Gearings

Chernets, Myron; Kindrachuk, Myroslav; Kornienko, Anatolii; Yurchuk, Alina

doi:10.2478/ama-2020-0029

Abstract

The method of model triboexperimental studies to determine the basic mathematical model parameters of materials wear resistance at sliding friction is considered. The quantitative relative experimental characteristics of wear resistance of glass fibre and carbon fibre reinforced polyamide used in metal-polymer gear couple have been determined. Wear resistance functions of these functional polymeric composites have been established as the basic ones in the tribokinetic mathematical model of material wear for sliding friction conditions. Also, according to the conducted researches, wear resistance diagrams were constructed. They may be used as graphical indicators of wear resistance in the required range of specific friction forces. The dependences that connect the characteristic functions of wear resistance of these materials (obtained by the developed mathematical tribokinetic wear model) with linear wear and gearing service life are presented.

References

1. Bajpaj P., Kahraman A., Anderson N.E. (2004), A surface wear prediction methodology for parallel-axis gear pairs, Journal of Tribology, 126, 597–605.10.1115/1.1691433
Search in Google Scholar Back to article
2. Bobach L., Beilicke R., Bartel D., Deters L. (2012), Thermal elastohydrodynamic simulation of involute spur gears incorporating mixed friction, Tribology International, 48, 191–206.10.1016/j.triboint.2011.11.025
Search in Google Scholar Back to article
3. Bongaerts J. H. H., Day J. P. R., Marriott C.,. Pudney P. D. A, Williamson A.-M. (2018), In situ confocal Raman spectroscopy of lubricants in a soft elastohydrodynamic tribological contact, Journal of applied physics, 104, 014913.10.1063/1.2952054
Search in Google Scholar Back to article
4. Brandão J.A., Seabra J.H.O., Castro J.D., Martins R. (2014), On the simulation of simultaneous fatigue and mild wear during a micro-pitting gear test, International Gear Conference: 26th–28th August 2014, Lyon, P. 523–531.
Search in Google Scholar Back to article
5. Brauer J., Andersson S. (2003), Simulation of wear in gears with flank interference – a mixed FE and analytical approach, Wear, 254, 1216–1232.10.1016/S0043-1648(03)00338-7
Search in Google Scholar Back to article
6. Bravo A., Koffi D., Toubal L., Erchiqui F. (2015), Life and damage mode modeling applied to plastic gears, Engineering Failure Analysis, 58, 1, 113–133.10.1016/j.engfailanal.2015.08.040
Search in Google Scholar Back to article
7. Brethee K, Zhenc D., Gua F., Ball A (2017), Helical gear wear monitoring: Modelling and experimental validation, Mechanism and Machine Theory, 117, 210–229.10.1016/j.mechmachtheory.2017.07.012
Search in Google Scholar Back to article
8. Cherepova T., Dmitrieva G., Tisov O., Dukhota O., Kindrachuk M. (2018), Research on the properties of Co-Tic and Ni-TiC hip-sintered alloys, Acta mechanica et automatica, 13, 1, 57–67.10.2478/ama-2019-0009
Search in Google Scholar Back to article
9. Chernets M. (2019a), A method for predicting contact strength and life of archimedes and involute worm gears, considering the effect of wear and teeth correction, Tribology in Industry, 41, 1, 134–141.10.24874/ti.2019.41.01.15
Search in Google Scholar Back to article
10. Chernets M. (2019b), Method of calculation of tribotechnical characteristics of the metal-polymer gear, reinforced with glass fiber, taking into account the correction of tooth, Eksploatacja i Niezawodnosc – Maintenance and Reliability, 21, 4, 546–552.10.17531/ein.2019.4.2
Search in Google Scholar Back to article
11. Chernets M., Chernets Ju. (2017) The simulation of influence of engagement conditions and technological teeth correction on contact strength, wear and durability of cylindrical spur gear of electric locomotive, Proc. JMechE. Part J: Journal of Engineering Tribology, 231, 1, 57 – 62.
Search in Google Scholar Back to article
12. Chernets M.V., Kelbinski J., Jarema R.Ja. (2011), Generalized method for the evaluation of cylindrical involute gears, Materials Science, 1, 45–51.10.1007/s11003-011-9366-9
Search in Google Scholar Back to article
13. Chernets’ M.V., Lenik K. (1997), On estimation of materials durability, Materials science, 33, 834–840.10.1007/BF02355563
Search in Google Scholar Back to article
14. Drozdov Ju. N. (1969), The calculation of gear trains wear resistance [In Russian], Mashinovedenie, 2, 84–88.
Search in Google Scholar Back to article
15. Drozdov Ju. N. (1975), Development of wear calculation method and friction simulation [In Russian], Wear resistance, Science, Moscow, 120–135.
Search in Google Scholar Back to article
16. Drozdov Ju.N., Nazhestkin B.P. (1990), The development of methods to calculate weaer of toothed wheels [In Russian], Engineering Gerald, 11, 15–17.
Search in Google Scholar Back to article
17. Feng K., Borghesani P., Smith W. A., Randall R.B., Peng Z. (2019), Vibration-based updating of wear prediction for spur gears, Wear, 426–427, part B, 1410–1415.10.1016/j.wear.2019.01.017
Search in Google Scholar Back to article
18. Flodin A. (2000) Wear of spur and helical gears. Dissertations and Theses, UMJ Dissertations Publishing.
Search in Google Scholar Back to article
19. Flodin A., Andersson S. (1997), Simulation of mild wear in spur gears, Wear, 207, 1–2, 16–23.10.1016/S0043-1648(96)07467-4
Search in Google Scholar Back to article
20. Flodin A., Andersson S. (1999), Wear simulation of spur gears, Lubrication science, 5(3), 225–250.10.1002/tt.3020050303
Search in Google Scholar Back to article
21. Flodin A., Andersson S. (2000), Simulation of mild wear in helical gears, Wear, 241(2), 123–128.10.1016/S0043-1648(00)00384-7
Search in Google Scholar Back to article
22. Flodin A., Andersson S. A (2000), Simplified model for wear prediction in helical gears, Wear, 249 (3–4), 285–292.10.1016/S0043-1648(01)00556-7
Search in Google Scholar Back to article
23. Gębura A., Kłysz S., Tokarski T. (2019), Monitoring wear of gear wheel of helicopter transmission using the FAM-C and FDM-A methods, Procedia Structural Integrity, 16, 184–191.10.1016/j.prostr.2019.07.039
Search in Google Scholar Back to article
24. Gorokh G., M.I.Pashechko M., Borc J., Lozovenko A., Kashko I., Latos A. (2018), Matrix coatings based on anodic alumina with carbon nanostructures in the pores, Applied surface science, 433, 1, 829–835.10.1016/j.apsusc.2017.10.117
Search in Google Scholar Back to article
25. Greco A.C., Erck R., Ajayi O., Fenske G. (2011), Effect of reinforcement morphology on high-speed sliding friction and wear of PEEK polymers, Wear, 271, 9–10, 2222–2229.10.1016/j.wear.2011.01.065
Search in Google Scholar Back to article
26. Grib V.V. (1982), Solwing of tribotechnical problems by numerical methods [In Russian], Science, Noscow.
Search in Google Scholar Back to article
27. Guilbault R., Lalonde S. (2019), A stochastic prediction of roughness evolution in dynamic contact modelling applied to gear mild wear and contact fatigue, Tribology International, 140, 10585410.1016/j.triboint.2019.105854
Search in Google Scholar Back to article
28. Hegadekatte V., Hilgert J., Kraft O., Huber N. (2010), Multi time scale simulations for wear prediction in micro-gears, Wear, 268, 316–32410.1016/j.wear.2009.08.017
Search in Google Scholar Back to article
29. Kahraman A., Bajpaj P., Anderson N.E. (2005), Influence of tooth profile deviations on helical gear wear, Journal of mechanical design, 127, 4, 656–663.10.1115/1.1899688
Search in Google Scholar Back to article
30. Kindrachuk M., Volchenko A,. Volchenko D, Volchenko N., Poliakov P., Tisov O., Kornienko A. (2019b) Polymeres with enhanced energy capacity modified by semiconductor materials, Functional materials, 26, 3, 629–634.10.15407/fm26.03.629
Search in Google Scholar Back to article
31. Kindrachuk M.V., Volchenko O.I., Volchenko D.O., Volchenko N.O., Polyakov P.A., Kornienko A.O., Yurchuk A.O. (2019a), Polymeric Materials Modified by Semiconductor Substances in Friction Units of Braking Devices, Journal on nano- and electronic physics, 11, 3, 03014.10.21272/jnep.11(3).03014
Search in Google Scholar Back to article
32. Kindrachuk V., Galanov B. (2014), An efficient approach for numerical treatment of some inequalities in solid mechanics on examples of Kuhn–Tucker and Signorini–Fichera conditions, Journal of the Mechanics and Physics of Solids, 63, 432–450.10.1016/j.jmps.2013.08.008
Search in Google Scholar Back to article
33. Kolivand M., Kahraman A. (2010), An ease-off based method for loaded tooth contact analysis of hypoid gears having local and global surface deviations, Journal of mechanical design, 132, 7, 071004.10.1115/1.4001722
Search in Google Scholar Back to article
34. Kurdi A, Hongjian Wang H, Chang L. (2018), Effect of nano-sized TiO2 addition on tribological behaviour of poly ether ether ketone composite, Tribology International, 117, 225–235.10.1016/j.triboint.2017.09.002
Search in Google Scholar Back to article
35. Liu H., Liu H., Zhu C., Tang J. (2020), Study on gear contact fatigue failure competition mechanism considering tooth wear evolution, Tribology International, 147, 106277 (Journal pre-proof).10.1016/j.triboint.2020.106277
Search in Google Scholar Back to article
36. Liu, X., Yang, Y., Zhang, J. (2016), Investigation on coupling effects between surface wear and dynamics in a spur gear system, Tribology International, 101, 383–394.10.1016/j.triboint.2016.05.006
Search in Google Scholar Back to article
37. Mao K. (2007), Gear tooth contact analysis and its application in the redaction of fatigue wear, Wear, 262, 11/12, 1281–1288.10.1016/j.wear.2006.06.019
Search in Google Scholar Back to article
38. Pashechko M., Krzysztof Dziedzic K., Mendyk E., Jerzy Jozwik J. (2018), Chemical and phase composition of the friction surfaces Fe– Mn–C–B–Si–Ni–Cr hardfacing coatings, Journal of tribology, 140(2), 021302.10.1115/1.4037953
Search in Google Scholar Back to article
39. Pasta A., Mariotti Virzi G. (2007), Finite element method analysis of a spur gear with a corrected profile, Journal of strain analysis, 42, 281–292.10.1243/03093247JSA284
Search in Google Scholar Back to article
40. Pronikov A. S. (1978), Reliability of machines [In Russian], Machine engineering, Moscow.
Search in Google Scholar Back to article
41. Raadnui S. (2019) Spur gear wear analysis as applied for tribological based predictive maintenance diagnostics, Wear, 268, 316–324.10.1016/j.wear.2018.12.088
Search in Google Scholar Back to article
42. Wang H., Zhou C., Leia Y., Liu Z. (2019), An adhesive wear model for helical gears in line-contact mixed elastohydrodynamic lubrication, Wear, 426–427, part A, 896–909.10.1016/j.wear.2019.01.104
Search in Google Scholar Back to article
43. Wang, Y., Wang, Q. J. (2013), Stribeck Curves. Encyclopedia of Tribology, 3365–33150.10.1007/978-0-387-92897-5_148
Search in Google Scholar Back to article
44. Wei J., Niu R., Dong Q., Zhang S. (2020), Fretting-slipping fatigue failure mode in planetary gear system, International Journal of Fatigue, 136, 105632.10.1016/j.ijfatigue.2020.105632
Search in Google Scholar Back to article
45. Wu S., Cheng H.S. (1993), Sliding wear calculation in spur gears, Journal of Tribology, 115, 493–500.10.1115/1.2921665
Search in Google Scholar Back to article
46. Zorkoa D, Kulovec S, Duhovnika J, Tavcar J. (2019), Durability and design parameters of a Steel/PEEK gear pair, Mechanisms and machine theory, 140, 825–846.10.1016/j.mechmachtheory.2019.07.001
Search in Google Scholar Back to article

Experimental Estimation of Wear Resistance of Polyamide Composites, Reinforced By Carbon and Glass Fibres Used in Metal-Polymer Gearings

Abstract

Paradigm

My account