Investigation on the preparation and mechanical properties of porous Cu35Ni15Cr alloy for a molten carbonate fuel cell

Li, Cong; Chen, Jian; Li, Wei; Ren, Yanjie; He, Jianjun

doi:10.1515/msp-2015-0113

Abstract

The preparation process of porous Cu35Ni15Cr alloy was studied in this paper. The effect of ball milling time and sintering temperature on the porosity of Cu35Ni15Cr alloy was identified. It was found that 18 h ball milling and 950 °C sintering are the most promising parameters for the preparation of porous Cu35Ni15Cr alloy. The products have a ~62 % porosity. The alloy consists of an α phase and β phase. The influence of deformation temperature and loading rate on the mechanical properties of Cu35Ni15Cr alloys was investigated. The results show that with decreasing deformation temperature, the yield strength and elastic modulus of the porous alloy increase. With the increase of loading rate, the yield strength of these alloys shows an increasing trend, but the elastic modulus is on a steady level.

References

[1] Frangini S., J. Power Sources, 182 (2008), 462.10.1016/j.jpowsour.2007.11.100
Search in Google Scholar
[2] Andujar J.M., Segrua F., Renew Sustain Ener. Rev., 13 (2009), 2309.
Search in Google Scholar
[3] Li G., Thomas B.G., Stubbins J.F., Metall. Mater. Trans. A, 31 (2000), 2491.10.1007/s11661-000-0194-z
Search in Google Scholar
[4] Tsuyoshi N., Vinay G., Yoshimi O., Meiten K., Ram N.S., Alain T., Etienne D., J Power Sources, 104 (2002), 181.10.1016/S0378-7753(01)00910-7
Search in Google Scholar
[5] Chawla N., Deng X., Mat. Sci. Eng. A-Struct., 390 (2005), 98.10.1016/j.msea.2004.08.046
Search in Google Scholar
[6] Cedergren J., Melin S., Lidstrom P., Power Technol., 160 (2005), 161.10.1016/j.powtec.2005.08.023
Search in Google Scholar
[7] Wee J.H., Mater. Chem. Phys., 98 (2006), 273.10.1016/j.matchemphys.2005.09.018
Search in Google Scholar
[8] Kim D., Lee I., Lim H., Lee D., J. Power Sources, 109 (2002), 347.10.1016/S0378-7753(02)00085-X
Search in Google Scholar
[9] Kim Y.S., Lee K.Y., Chun H.S., J. Power Sources, 99 (2001), 26.10.1016/S0378-7753(00)00689-3
Search in Google Scholar
[10] Wee J.H., Mater. Chem. Phys., 101 (2007), 322.10.1016/j.matchemphys.2006.06.006
Search in Google Scholar
[11] Lee H., Lee I., Lee D., Lim H., J. Power Sources, 162 (2006), 1088.10.1016/j.jpowsour.2006.07.072
Search in Google Scholar
[12] Kim G., Moon Y., Lee D., J. Power Sources, 104 (2002), 181.10.1016/S0378-7753(01)00910-7
Search in Google Scholar
[13] Lei P., Chen J., Li W., Ren Y.J., Qiu W., Chen J.L., Appl. Mech. Mat., 303 (2013), 2490.10.4028/www.scientific.net/AMM.303-306.2490
Search in Google Scholar
[14] Chen J., Huang Z.H., Li W., Ren Y.J., He Z., Qiu W., He J.J., Chen J.L., Key Eng. Mat., 573 (2014), 105.10.4028/www.scientific.net/KEM.573.105
Search in Google Scholar
[15] Wang B., Zhang E., Int. J. Mech. Sci., 50 (2008), 550.
Search in Google Scholar
[16] Kim Y.S., Chun H.S., J. Power Source, 84 (1999), 80.10.1016/S0378-7753(99)00306-7
Search in Google Scholar
[17] Hwang E.R., Park J.W., Kim Y.D., Kim S.J., Kang S.G., J. Power Source, 69 (1997), 55.10.1016/S0378-7753(97)02566-4
Search in Google Scholar

Investigation on the preparation and mechanical properties of porous Cu35Ni15Cr alloy for a molten carbonate fuel cell

Abstract

Paradigm

My account