Experimental Data in Vehicle Modeling

Tomasikova, Maria; Sojcak, Dusan; Nieoczym, Aleksander; Brumercik, Frantisek

doi:10.1515/logi-2017-0010

Abstract

This article is about a vehicle model which is created in software Matlab Simscape Driveline. In this model the motor is created like a subsystem by Simulink blocks and input data were measured by single roller dynamometer for cars (SRD). Measured data are the input into the model by Lookup Table block. The vehicle model is made by gear, differential, tire and vehicle body blocks. We studied the forces on tires, the vehicle velocity and the slip.

References

[1] Kohar, R. & Hrcek, S. (2014). Dynamic analysis of a rolling bearing cage with respect to the elastic properties of the cage for the axial and radial load cases. Communications, 16 (3A), 74-81. ISSN 1335-4205.10.26552/com.C.2014.3A.74-81
Search in Google Scholar Back to article
[2] Hrcek, S., Kohar, R. & Medvecky, S. (2012). Determination on the maximum roller bearing load with regards to durability thereof using FEM analysis. Communications, 14 (3), 55-61. ISSN 1335-4205.10.26552/com.C.2012.3.55-61
Search in Google Scholar Back to article
[3] Drozdziel, P., Brumercikova, E. & Bukova, B. (2015). The Use of Progressive Methods of Serving Passengers. Transport problems, 10 (4). ISSN 1896-0596.
Search in Google Scholar Back to article
[4] Nieoczym, A. (2005). Application of a transportation flux for determining qualitative indices. Communications, 7 (1), 47-48. ISSN 1335-4205.10.26552/com.C.2005.1.47-48
Search in Google Scholar Back to article
[5] Kucera, L., Lukac, M., Jurak, L. & Brumercik, F. (2009). Hydromechanical Automatic Transmission. Communications, 11 (2), 33-35. ISSN 1335-4205.10.26552/com.C.2009.2.33-35
Search in Google Scholar Back to article
[6] Drozdziel, P. & Krzywonos, L. (2009). The Estimation of the Reliability of the First Daily Diesel Engine Start-up During its Operation in the Vehicle. Eksploatacja i Niezawodnosc – Maintenance and Reliability, 1 (41), 4-10. ISSN 1507-2711.
Search in Google Scholar Back to article
[7] Jedlinski, L., Caban, J., Krzywonos, L., Wierzbicki, S. & Brumercik, F. (2015). Application of vibration signal in the diagnosis of IC engine valve clearance. Journal of Vibroengineering, 17 (1), 175-187. ISSN 1392-8716.
Search in Google Scholar Back to article
[8] Lukac, M., Brumercik, F., Krzywonos, L. & Drozdziel, P. (2014). Tension mechanism dynamic analysis. Communications, 16 (3A), 184-188. ISSN 1335-4205.10.26552/com.C.2014.3A.184-188
Search in Google Scholar Back to article
[9] Filo, M. & Lukac, M. (2005). Modeling and Simulation of Mechanisms with Computer Support, Zilina: EDIS-publisher of University of Zilina, ISBN 80-8070-466-X.
Search in Google Scholar Back to article
[10] Caban, J., Drozdziel, P., Vrabel, J., Sarkan, B., Marczuk, A., Krzywonos, L. & Rybicka, I. (2016). The research on ageing of glycol-based brake fluids of vehicles in operation. Advances in Science and Technology, 10 (32), 9-16. ISSN 2299-8624.10.12913/22998624/65113
Search in Google Scholar Back to article
[11] Caban, J., Marczuk, A., Sarkan, B. & Vrabel, J. (2015). Studies on operational wear of glycol-based brake fluid. Przemysł Chemiczny, 94 (10), 1802-1806. ISSN 0033-2496.
Search in Google Scholar Back to article
[12] Faturik, L., Trsko, L., Hrcek, S. & Bokuvka, O. (2014). Comparison of structural design in high and ultra-high cycle fatigue regions. Transactions of FAMENA, 38 (4), 1-12. ISSN 1333-1124.
Search in Google Scholar Back to article
[13] Marczuk, A., Caban, J., Savinykh, P., Turubanov, N. & Zyryanov, D. (2017). Maintenance research of a horizontal ribbon mixer. Eksploatacja i Niezawodnosc – Maintenance and Reliability, 19 (1), 121-125. ISSN 1507-2711.
Search in Google Scholar Back to article
[14] Walczak, M., Zwierzchowski, M., Bienias, J. & Caban, J. (2017). The tribological characteristics of Al-Si/graphite composite. Tribologia, 1, 97-104. ISSN 0208-7774.
Search in Google Scholar Back to article

Experimental Data in Vehicle Modeling

Abstract

Paradigm

My account