References
- 1. Bujurke N.M., Kudenatti R.B., Awati V.B. (2007), Effect of surface roughness on squeeze film poroelastic bearings with special reference to synovial joints, Mathematical Biosciences, 209, 76-89.
- 2. Christensen H. (1970), Stochastic model for hydrodynamic lubrication of rough surfaces, Proc. Inst. Mech. Engrs, 184, No. 1, 1013-1022.
- 3. Christensen H., Tønder K. (1971), The hydrodynamic lubrication of rough bearing surfaces of finite width, ASME, J. Lubric. Technol., 93(2), 324-330.
- 4. Christensen H., Tønder K. (1973), The hydrodynamic lubrication of rough journal bearings, ASME, J. Lubric. Technol., 95(1), 166-172.
- 5. Dorier C., Tichy J. (1992), Behaviour of a Bingham-like viscous fluid in lubrication flows, J. Non-Newt. Fluid Mech., 45(3), 291-350.
- 6. Gururajan K., Prakash J. (1999), Surface roughness effects in infinitely long porous journal bearing, Journal of Tribology, Trans. ASME, 121(1), 139-147.
- 7. Khonsari M.M., Dai F. (1992), On the mixture flow problem in lubrication of hydrodynamic bearing: small solid volume fraction, STLE Trib. Trans., 35(1), 45-52.
- 8. Lin J.-R. (2000), Surfaces roughness effect on the dynamic stiffness and damping characteristics of compensated hydrostatic thrust bearings, Int. J. Machine Tools Manufact., 40, 1671-1689.
- 9. Lin J.-R. (2001), The effect of couple stresses in the squeeze film behavior between isotropic rough rectangular plates, Int. J. Appl. Mech. Eng., 6(4), 1007-1024.
- 10. Lipscomb C.C., Denn M.M. (1984), Flow of Bingham fluids in complex geometries, J. Non-Newt. Fluid Mech., 14(3), 337-349.
- 11. Morgan V.T., Cameron A. (1957), Mechanismus of lubrication in porous metal bearings, Proc. Conf. on Lubrication and Wear, Inst. Mech. Eng., 151-157, London.
- 12. Prakash J., Tiwari K. (1984), An analysis of the squeeze film between rough porous rectangular plates with arbitrary porous wall thickness, Journal of Tribology, Trans. ASME, 106(2), 218-222.
- 13. Prakash J., Tiwari K. (1985), Effects of surface roughness on the squeeze film between rectangular porous annular disc with arbitrary porous wall thickness, Int. J. Mech. Sci., 27(3), 135-144.
- 14. Rajalingam C., Rao B.V.A., Prabu S. (1978), The effect of a non-Newtonian lubricant on piston ring lubrication, Wear, 50, 47-57.
- 15. Rotem Z., Shinnar R. (1961), Non-Newtonian flow between parallel boundaries in linear movements, Chem. Eng. Sie., 15, 130-143.
- 16. Swamy S.T.N., Prabhu B.S., Rao B.V.A. (1975), Stiffness and damping characteristics of finite width journal bearing with a non-Newtonian film and their application to instability prediction, Wear, 32, 379-390.
- 17. Wada S., Hayashi H. (1971), Hydrodynamic lubrication of journal bearings by pseudo-plastic lubricants, Pt 1, Theoretical studies, Pt 2, Experimental studies, Bull. JSME, 14(69), 268-286.
- 18. Walicka A. (1989), Accurate and Asymptotic Solution of Simplified Sets of Equations Describing the Motion of Viscous Fluids in a Slot Bounded by Two Co-axial Surfaces of Revolution (in Polish), PWN, Warszawa.
- 19. Walicka A. (1994), Micropolar flow in a Slot Between Rotating Surfaces of Revolution, TU Press, Zielona Gora.
- 20. Walicka A. (2002), Rotational Flows of Rheologically Complex Fluids in Thin Channels (in Russian), University Press, Zielona Gora.
- 21. Walicka A. (2009), Surface roughness effects in a curvilinear squeeze film bearing lubricated by a power-law fluid, Int. J. Appl. Mech. Engng, 14(1), 277-293.
- 22. Walicka A. (2012), Porous curvilinear squeeze film bearing with rough surfaces lubricated by a power-law fluid, Journal of Porous Media, 15(1), 29-49.
- 23. Walicka A., Walicki E. (2002a), Surface roughness effect on the pressure distribution in curvilinear thrust bearings, Exploitation Problems of Machines, 131(3), 157-167.
- 24. Walicka A., Walicki E. (2002b), Couple stress and surface roughness effects in curvilinear thrust bearings, Int. J. Appl. Mech. Engng, Vol. 7, Spec. Issue: SITC, 109-117.
- 25. Walicki E. (1975), Viscous fluid flow in a slot of the curvilinear thrust bearing, Rev. Roum. Sci. Techn. - Mech. Appl., 20(4), 483-493.