Influence of different hard-facing procedures on quality of surfaces of regenerated gears
References
- Arsić, D., Lazić, V., Nikolić, R., Mutavžić, M., Sedmak, A., Hadzima, B., 2016a. Possibility for realizing savings by application of the hard-facing as the revitalization technology of various machine parts, in Technical aspects of materials quality. Eds. Pietraszek, J., Klimecka-Tatar, D., Managers of Quality and Production Association, Czestochowa, Poland, Chapter 8, 111–144.
- Arsić, D., Lazić, V., Mitrović, S., Džunić, D., Aleksandrović, S., Djordjević, M., Nedeljković, B., 2016b. Tribological Behavior of Four Types of Filler Metals for Hard Facing Under Dry Conditions. Industrial Lubrication and Tribology, 68(6), 729–736, DOI: 10.1108/ILT-10-2015-0156
- Atxaga, G., Irisarri, A.M., 2010. Failure analysis of the end of a shaft of an engine. Engineering Failure Analysis, 17(4), 714–721, DOI: 10.1016/j.engfailanal.2009.08.010
- Bai, H., Zhu, C., Zhou, Y., Chen, X., Feng, H., Ye, W., 2020. Study on Tooth Interior Fatigue Fracture Failure of Wind Turbine Gears. Metals, 10(11), 1497, DOI: 10.3390/met10111497
- Borrego, L.P., Pires, J.T., Costa, J.M., Ferreira, J.M., 2009. Mould steels repaired by laser welding. Engineering Failure Analysis, 16(2), 596–607, DOI: 10.1016/j.engfailanal.2008.02.010
- Czuprynski, A., 2020. Comparison of properties of hardfaced layers made by a metal-core-covered tubular electrode with a special chemical composition. Materials, 13, 5445, DOI: 10.3390/ma13235445
- Dadon, I., Koren, N., Klein, R., Lipsett, M.G., Bortman, J., 2020. Impact of gear tooth surface quality on detection of local faults. Engineering Failure Analysis, 108, 104291, DOI: 10.1016/j.engfailanal.2019.104291
- Desir, J.L., 2001. Examples of Repair Welding of Heavy Machinery Subject to Breakage due to Low Frequency Alternating Stresses. Engineering Failure Analysis, 8(5), 423–434, DOI: 10.1016/S1350-6307(00)00046-7
- Durmuş, H., Çömez, N., Gül, C., Yurddaşkal, M., Yurddaşkal, M., 2018. Wear performance of Fe-Cr-C-B hardfacing coatings: Dry sand/rubber wheel test and ball-on-disc test. International Journal of Refractory Metals and Hard Materials, 77, 37–43, DOI: 10.1016/j.ijrmhm.2018.07.006
- EN 14700:2014: Welding consumables — Welding consumables for hard-facing.
- EN 1599:1997: Welding consumables — Covered electrodes for manual arc welding of creep-resisting steels - Classification.
- Feng W., Feng Z., Mao L., 2020. Failure analysis of a secondary driving helical gear in transmission of electric vehicle. Engineering Failure Analysis, 117, 104934, DOI: 10.1016/j.engfailanal.2020.104934
- Gualco, A., Marini, C., Svoboda, H., Surian, E., 2015. Wear resistance of Fe-based nanostructured hardfacing. Procedia Material Science, 8, 934–943, DOI: 10.1016/j.mspro.2015.04.154
- Hao, F., Liao, B., Li, D., Liu, L., Dan, T., Ren, X., Yang, Q., 2011. Effects of rare earth oxide on hardfacing metal microstructure of medium carbon steel and its refinement mechanism. Journal of Rare Earths, 29(6), 609–613, DOI: 10.1016/S1002-0721(10)60507-8
- Lazić, V., Sedmak, A., Aleksandrović, S., Milosavljević, D., Čukić, R., Grabulov, V., 2009. Reparation of damaged mallet for hammer forging by hard facing and weld cladding. Tehnički vjesnik - Technical Gazette, 16(4), 107-113, https://hrcak.srce.hr/45753
- Lazić, V., Čukić, R., Aleksandrović, S., Milosavljević, D., Arsić, D., Nedeljković, B., 2014. Techno-economic justification of reparatory hard facing of various working parts of mechanical systems. Tribology in Industry, 36(3), 287–292, http://www.tribology.fink.rs/journals/2008/2008-1-2/1.pdf
- Lazić, V., Arsić, D., Nikolić, R., Mutavdžić, M., Meško, J., 2016. Reparation by Hard Facing of the Damaged Secondary Stone Crusher. Manufacturing Technology, 16(2), 375–380, https://www.journalmt.com/artkey/mft-201602-0012_reparation-by-hard-facing-of-the-damaged-secondary-stone-crushers.php
- Li, D., Yang, Y., Liu, L., Zhang, J., Yang, Q., 2009. Effects of RE oxide on the microstructure of hardfacing metal of the large gear. Material Science and Engineering A, 509, 94–97, DOI: 10.1016/j.msea.2009.02.018
- Markovic, S., Milovic, Lj., Marinkovic, A., Lazovic, T., 2011. Tribological aspect of selecting filler metal for repair surfacing of gears by hardfacing. Structural Integrity and Life, 11(2), 127–130, http://divk.inovacionicen-tar.rs/ivk/ivk11/127-130-IVK2-2011-SM-LM-AM-TL.pdf
- Marković, S., Arsić, D., Nikolić, R., Lazić, V., Hadzima, B., Milovanović, V., Dwornicka, R., Ulewicz, R., 2021. Exploitation characteristics of teeth flanks of gears regenerated by three hard-facing procedures. Materials, 14(15), paper no. 4203, DOI: 10.3390/ma14154203
- Marković, S., Arsić, D., Nikolić, R.R., Lazić, V., Ratković, N., Hadzima, B., Szmidla, J., Ulewicz, R., 2021. Analysis of the Welding Type and Filler Metal Influence on Performance of a Regenerated Gear. Materials, 14(6), 1496, DOI: 10.3390/ma14061496
- Mohammed, O.D., Rantatalo, M., 2020. Gear Fault Models and Dynamics-Based Modelling for Gear Fault Detection - A Review. Engineering Failure Analysis, 117, 104798, DOI: 10.1016/j.engfailanal.2020.104798
- Suraj, R., 2021. Hardfacing and its effect on wear and corrosion performance of various ferrous welded mild steels. Materials Today: Proceedings, 42, 842–850, DOI: 10.1016/j.matpr.2020.11.592
- Tomić, R., 2019. Influence of Tribological Pairs on Structural and Material Damage. Structural Integrity and Life, 19 (1), 58–66, http://divk.inovacionicentar.rs/ivk/ivk19/058-IVK1-2019-RT.pdf
- Trško, L., Lago, J., Jambor, M., Nový, F., Bokůvka, O., Florková, Z., 2020. Microstructure and residual stress analysis of Strenx 700 MC welded joint. Production Engineering Archives, 6, 41–44, DOI: 10.30657/pea.2020.26.09
- Ulewicz, R., Novy, F.R., 2016. The influence of the surface condition on the fatigue properties of structural steel. Journal of Balkan Tribological Association, 22, 1147–1155, https://scibulcom.net/en/article/39wnZZhcNDoMsJzVTXq8
- Vasić, M., Stojanović, B., Blagojević, M., 2020. Fault Analysis of Gearboxes in Open Pit Mine. Applied Engineering Letters, 5(2), 50–61, DOI: 10.18485/-aeletters.2020.5.2.3
- Vicen, M., Bokuvka, O., Nikolić, R., Bronček, J., 2020. Tribological behavior of low-alloyed steel after nitriding. Production Engineering Archives, 26(3), 78–83, DOI: 10.30657/pea.2020.26.16
- Vicen, M., Bronček, J., Nový, F., 2019. Investigation of tribological properties of CarbonX coating deposited on 100Cr6 steel. Production Engineering Archives, 25, 52–55, DOI: 10.30657/pea.2019.25.10
- Xing, S., Yu, S., Deng, Y., Dai, M., Yu, L., 2012. Effect of Cerium on abrasive wear behaviour of hardfacing alloy. Journal of Rare Earths, 30, 69–73, DOI: 10.1016/S1002-0721(10)60641-2
- Yousfi, B.E., Soualhi, A., Medjaher, K., Guillet, F., 2020. New Approach for Gear Mesh Stiffness Evaluation Of Spur Gears With Surface Defects. Engineering Failure Analysis, 116, 104740, DOI: 10.1016/j.engfailanal.2020.104740
Language: English
Page range: 257 - 264
Submitted on: Aug 19, 2021
Accepted on: Sep 26, 2021
Published on: Nov 20, 2021
Published by: Quality and Production Managers Association
In partnership with: Paradigm Publishing Services
Publication frequency: 4 issues per year
Related subjects:
© 2021 Ružica R. Nikolić, Svetislav Marković, Dušan Arsić, Vukić Lazić, Branislav Hadzima, Robert Ulewicz, published by Quality and Production Managers Association
This work is licensed under the Creative Commons Attribution-ShareAlike 4.0 License.